Models
>
31AH6WTS710
31AH6WTS710 (2008) Cub Cadet Snow Blower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: ...
In Stock
Order now and your part arrives by Sep 6
$6.51
This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread si...
In Stock
Order now and your part arrives by Sep 6
This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of ...
In Stock
Order now and your part arrives by Sep 6
This is a self-tapping screw for your lawn equipment. It has multiple applications, and is made of durable metal. This part is sold individually. To install this screw, you will need a wrench. The maj...
In Stock
Order now and your part arrives by Sep 6
$6.51
This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torqu...
In Stock
Order now and your part arrives by Sep 6
$33.20
This replacement V-Belt is a genuine OEM sourced part, not an aftermarket imitation. It is commonly utilized on snow blowers. This is the drive belt that would spin the augers. Inspect belts periodica...
In Stock
Order now and your part arrives by Sep 6
In Stock
Order now and your part arrives by Sep 6
In Stock
Order now and your part arrives by Sep 6
$6.55
This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with...
In Stock
Order now and your part arrives by Sep 6
$6.83
This item is available as an individual replacement part that has been OEM sourced to be used with snowthrowers from Craftsman. The metal spacer is part of the auger assembly and it is used to separat...
In Stock
Order now and your part arrives by Sep 6
$8.23
This is a genuine replacement part manufactured for use with lawn and garden power equipment. This versatile screw has a flanged hex head and can be used in a variety of applications. The screw is ava...
In Stock
Order now and your part arrives by Sep 6
$32.12
This flat idler pulley is designed to help maintain proper belt tension while reducing vibration and uneven wear in lawn and snow equipment drive systems. Made from durable metal for long-lasting perf...
In Stock
Order now and your part arrives by Sep 6
Common Problems and Symptoms for 31AH6WTS710
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Auger will not turn
Fixed by these parts
How to fix it
Cannot pull starter cord out or engine will not turn over
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dana from HAMMOND, IN
- Parts Used:
- 792006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Was this instruction helpful to you?
Thank you for voting!