Models
>
RT0701CX7
RT0701CX7 Makita Router
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for RT0701CX7
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
$35.26
This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing y...
In Stock
Order now and your part arrives by Apr 23
$19.19
This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is a M4 X 10 countersunk screw, and it is sold individually. This screw is compatible with various models, so its location may differ depending on your equipment. To fasten and unfasten this scre...
In Stock
Order now and your part arrives by Apr 23
$8.56
This item is an authentic Makita replacement part that has been OEM sourced and is intended to be used with routers. The base protector attaches to the bottom of the trimmer base and is used to provid...
In Stock
Order now and your part arrives by Apr 23
$9.63
This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or r...
In Stock
Order now and your part arrives by Apr 23
$22.15
This is a Rocker type switch that has internal terminals. This is a genuine Makita replacement part that is sold individually. rnrnSwitches are commonly replaced parts in tools. A switch handles on...
In Stock
Order now and your part arrives by Apr 23
$6.51
This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and p...
In Stock
Order now and your part arrives by Apr 23
$6.51
This brush cap is a genuine OEM sourced replacement part. It is commonly used on a variety of Makita power tools. This brush cap helps to secure the carbon brush in the brush holder. This cap has exte...
In Stock
Order now and your part arrives by Apr 23
$10.08
This part is available as an individual replacement part. The magnet sleeve goes between the stop ring and the wave washer. It is made of plastic and will require replacing if it becomes broken. A scr...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, table saws, masonry saws, planers, demolition hammers, and angle cutter...
In Stock
Order now and your part arrives by Apr 23
$6.51
This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out ...
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from HILLSBORO, OR
- Parts Used:
- 664064-4
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Old power cord frayed at the grommet entering the drill casing
Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Was this instruction helpful to you?
Thank you for voting!