The capacitor, also known as a run capacitor, is a component in your fridge that allows the compressor to cycle on and off to maintain a constant temperature. If your fridge and freezer are too warm i...
This genuine OEM part is an end cap for the door shelf retainer bar in your refrigerator. The end cap is used to secure the retainer bar and attach it to the fridge or freezer door. It is made of whit...
This is an OEM evaporator fan motor with an integrated wire harness for a refrigerator. It is in the back of the freezer where it pushes the air over the refrigerator coils, where the warm air cools a...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This hinge bracket, also known as a door stop, is attached to the bottom of the door and is used to limit how far the door swings out to protect the refrigerator itself, and any surrounding cabinets f...
This part is the replacement compartment door for your refrigerator. It is made of clear plastic and is approximately 9 inches by 6 inches. The compartment door snaps into the walls of the dairy compa...
This temperature sensor is for refrigerators.
The temperature sensor senses the temperature inside the refrigerator and sends information to the electronic control.
Unplug the refrigerator and s...
In Stock
Order now and your part arrives by May 10
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Susan
June 4, 2023
My freezer is freezing up. All the could are frosted over, then my Refrigerator temp drops. I have to defrost it every 2-3 days in the summer. My fav is working
For model number WRT108FZDB01
Hi Susan, thank you for reaching out. We have researched the model and would suggest checking the temperature sensor, part number FIX11753994. A faulty sensor might be affecting the defrost cycle resulting in low temperatures in the refrigerator section. We hope this information helps!
Me refrigerator isn't working. First the freezer freezes everything up. So the coils down the back are frosted over, then, the refrigerator part stops cooling. I'm pretty sure it's not self defrosting. How can I fix it
For model number WRT108FZDB01
Hello Susan, thank you for writing. For the initial freezing up and frosting over the issue can be Temperature sensor at evaporator in the freezer PS11753994. The issue of the fridge now not cooling at all is either the Capacitor PS11757023 or the Evaporator Fan PS11740359. We hope this helps.
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck le
... Read moret's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
The reason I repaired it myself was because the repairman that diagnosed the problem.didn't come back in two weeks. The evaporator fan sits behind a vented wall in the freezer and directs cold air into freezer and refrigerator.I removed the ice make assembly first and then the freezer wall held in place by two sheet metal nuts. Then remov
... Read moreed wires from fan motor. Removed the fan blade from fan motor,which was press fitted on,then removed fan motor from bracket assembly(make sure and retain the two vibration rubber washers on back and front of motor. Reinstall new motor with vibration washers and press fan blade on new motor. Install in bracket assemble and reassemnble.
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
