5VET6WPKLQ02 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Orland Hills, IL
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken elbow on icemaker water fill tube.
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Rayville, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights inside refrigerator not working
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from MINNEAPOLIS, MN
- Parts Used:
- 4387478
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Would Not Go On In The Refrigerator
First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James Richard from St. Cloud, MN
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Light Switch broke
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Texarkana, TX
- Parts Used:
- 2188462A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
freezer door gasket
It is pretty simple, if you lift the lip on inside of gasket there are 1/4 in. screws just loosen them but do not remove all the way just enough to get the gasket off and if needed a little more to get the new one back on. Then simply start putting the new gasket on and tighten screws as you go so it doesnt fall out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Albany, OR
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light switch on the refridgerator broke - no light.
Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.
The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.
I'm very pleased!
The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.
I'm very pleased!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sid from Houston, TX
- Parts Used:
- WP4387490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
bottom not cold and freezer back iced up
I automatically assumed it was the defrost timer contcts or motor due to 2 previous experiences. After seeing troubleshooting guide in check out page of partselect.com site I tested the 2 other components and found defective defrost thermostat. Thanks to this guide I saved a lot of time and cost.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard l. from franklin, KY
- Parts Used:
- WPW10567140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Ref was warm freezer was still freezing
check what site said was probably the problem 80% of the time. took out one screw unit dropped down disconnected part
connected new part screwed unit backup. Waited 4-5 hrs temp went from 60 degrees to 40.
connected new part screwed unit backup. Waited 4-5 hrs temp went from 60 degrees to 40.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bill from escondido, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
light inside fridge was flickering and clicking
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Santee, CA
- Parts Used:
- 2188448A
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set
gasket width and length about 1inch too short
I'm a retired auto mechanic....I thought this would be an easy job. I figured it would be easier if I removed the fresh food door which I did and it was straight forward. However the "folds" of the new gasket were different than the old one which I thought was an "update". But, after much struggling, I determined that the length and width of the new gasket were each about 1 inch shorter than the old one. When I decided to return the part, I was told that sometimes you have to soak the part in hot water. There were no instructions with the new part regarding this. I decided to buy a new refridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Kewanee, IL
- Parts Used:
- WP4387490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer was not defrosting
In the freezer section I disassembled the paneling and remeoved the old bi-metal by cutting the wires (make sure your cut has enough slack to do splicing). Then, stripped 1/4 inch of wire insulation from the wire and used a wire splice to connect the new bi-metal and after that I crimp the wire slice. After all of that, I reassembled the paneling plug in the refrigerator and presto!! (Unplugging the regfrigerator should be the first step). The paneling is easy to remove, all the tools that are required is 1/4" nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ocala, FL
- Parts Used:
- WP4387490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer Frosting
My problem was that the freezer was frosting up.
I have a no frost system so I decided to investigate.
I removed the panels inside the freezer compartment.
This took me about 5 minutes. After the ice had melted, I noticed that the clicks-on (bi-metal stat)
has the top push out at about a 45% angle.
After ordering a replacement, I pushed the top of the bi-metal down to where it's supposed to be.
Put the freezer back together and plugged it in. I needed the freezer while the part is being shipped.
The part arrived in about 3 days, which was very fast and a surprise to me.
The freezer was still working fine so I put the part in the drawer until I needed it.
That was in April 09 and it is still working. I have the part in case I need it.
I am very happy with the service I received from PartSelect and will recommend them to everyone.
David Daley
I have a no frost system so I decided to investigate.
I removed the panels inside the freezer compartment.
This took me about 5 minutes. After the ice had melted, I noticed that the clicks-on (bi-metal stat)
has the top push out at about a 45% angle.
After ordering a replacement, I pushed the top of the bi-metal down to where it's supposed to be.
Put the freezer back together and plugged it in. I needed the freezer while the part is being shipped.
The part arrived in about 3 days, which was very fast and a surprise to me.
The freezer was still working fine so I put the part in the drawer until I needed it.
That was in April 09 and it is still working. I have the part in case I need it.
I am very happy with the service I received from PartSelect and will recommend them to everyone.
David Daley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Manchester, TN
- Parts Used:
- WP3428970
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Refrigerator door hinge screw missing
Lost screw on bottom refrigerator door hinge which allowed the door to fall off. Purchased screw from Part Select for the Roper refrigerator. Drawings and parts list for this unit were available on their website. Easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Bolingbrook, IL
- Parts Used:
- 2188448A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The old seal had begun to split
After removing the old seal, I was able to mount the new seal on the inside panel. Then, as I replaced the screws, I learned that prior to tightening I needed to be sure that the flap was as far in as possible (between the inner panel and the door). I read on this website that someone used a hair dryer to make the seal maleable enough to ensure contact all around the door. That worked like a charm. I didn't even need to take the door off of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!