KRMF536RPS01 Whirlpool Refrigerator - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

Purchased new motor from Partselect.com. When it arrived it came with a new rubber washer that fitted on top of new motor that was not on old motor, that how water got into old motor. However, the instruction sheet did not give info on how to access the proper way to the motor that is the door. Not wanting to damage the freezer door assy. called in a tech who made it look easy, but even he had a little problem locating access panel that was directly under the motor in the freezer side of the door. After that it was a piece of cake.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.

The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.

To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

We were misled into believing we needed to replace the door seal, and after this replacement was completed we found out it was not the case.

Instead we needed to clean out the EXTENSION-DRAIN,DUAL EVAP W11661573, part #5 on the unit diagram, which is found on the back of the unit.

Back to the seal instructions:
Once you remove the original seal you cannot reuse it, so if you replace it and it is not what you needed, you can't return the not-needed part. There goes about $190.

Also, the seal comes with no instructions (at the time there was no instruction video here either and we had to search other sites). It turns out it takes at least 24 hrs for the rubber seal to regain its shape. You also may have to use a hair dryer for this pre-installation process. Because of this, I marked the time of repair as more than 2 hours.
The end of the instruction video we followed called for testing the new seal installation with a bill ($), if you can pull it out easily from the closed door, you need to continue heating the seal with the hair dryer to improve sealing.

So do yourself a favor and test you fridge seal first, to see if you really need to replace it. Close the door with a bill or paper trapped. If it is loose or falls out, seal needs to be replaced, if the bill/paper stays firm enough, the seal is fine.

It took a lot of research through other resources, not Partselect, to eventually fix the ice formation issue. From all the appliance repairs I have done, this was the most frustrating, although not the most complicated. Since no part needs to be purchased (though you could replace the drain tube for just $24 instead of hassle to clean it), no real help from parts stores is available, and you have to rely on random people with their home videos, some are reliable some are not. We could not find one with our model (596.72383411) and had to figure it out based on similar models. Our drain tube has a siphon, so it is a little harder to clean than other models with s straight tube.

Good luck!

I removed the ice bucket and motor cover on the inside of the left door. Then I removed the 4 screws that hold the motor in place and unplugged the electrical connector. The old motor shaft was all rusted and housing was cracked letting water inside the motor. That's why it failed. The new motor I ordered from Part select came with a rubber seal that I slipped on to the motor shaft. That will stop any water from entering the new dispencer motor. I reinstalled motor and the dispencer works great. Total time for removal and replace was 20 min. A novice can do it. Bill WI.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Very simple, easy, and quick! Anybody can do it!!

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After replacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.