WRT311FZDW06 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- garth from forest lake, MN
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
My refrigerator stopped cooling and the freezer section stopped freezing
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Middletown, NY
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Evaporator Fan failure
The reason I repaired it myself was because the repairman that diagnosed the problem.didn't come back in two weeks. The evaporator fan sits behind a vented wall in the freezer and directs cold air into freezer and refrigerator.I removed the ice make assembly first and then the freezer wall held in place by two sheet metal nuts. Then removed wires from fan motor. Removed the fan blade from fan motor,which was press fitted on,then removed fan motor from bracket assembly(make sure and retain the two vibration rubber washers on back and front of motor. Reinstall new motor with vibration washers and press fan blade on new motor. Install in bracket assemble and reassemnble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Crystal Beach, TX
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lower refrigerator not cooling
Looked up problem in your troubleshooting section, determined necessary part, ordered part on Saturday. Received part Tuesday. Installed in about 10 minutes. Works great. Saved about $200.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arnold, MD
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
power surge killed the fan motor
Removed back panel in the freezer. Removed old fan. Installed new fan and reinstalled back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerardo from el monte, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
compressor didnt turn on
changed the starter connected to the compressor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from GIBSONTON, FL
- Parts Used:
- W10861519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic on the shelf broke (too much weight in the drawer)
Remove the drawer. Remove top shelf it's connected to by carefully lifting. Turn the shelf upside down and slide meat drawer shelf off of either side, paying attention to how it is placed. Install new meat drawer shelf, replace shelf!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from ALVORD, TX
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Freezer working, not cold enough in fridge area.
Top freezer, remove fan cover on back panel in side top freezer, remove back panel inside top freezer, remove fan and fan motor, unplug electric from fan (PS unplug fridge first). Install new motor, replace ever thing in reverse. works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from REDLANDS, CA
- Parts Used:
- WP2315539
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Our refrigerator fan motor stopped working.
Most important, remove bracket attached to freezer rear wall and put entire fan motor assembly together, including attaching power supply, ground wire, front bracket and fan blade (be sure rubber vibration dampeners are in place on both brackets) THEN attach the whole assembly to the rear freezer wall! Doing it this way is so much easier, and you won't run the risk of losing a screw behind the condenser, as I did!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from CASTAIC, CA
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer was working fine but refrigerator would not go below 45 degrees
Removed back panel inside freezer replaced fan motor reinstalled panel and was done in about 40 minutes the video on part select explains the repair very accurately
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Miami, FL
- Parts Used:
- WPW10662129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The Freezer defrosted and everything on the top and the bottom spoiled
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stefanie from Sycamore, IL
- Parts Used:
- WP2156003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken end cap
Simple....snapped it right on...the important thing is that we ordered it for a reasonable price, and it arrived quickly...within 3 days. thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from NEWPORT, NC
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Evaporator fan in freezer.
I took the old fan out and replaced it with the new one,right easy task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from PITTSBURGH, PA
- Parts Used:
- W10803530
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
we bought a brand new fridge. It only had 1 shelf on door side for storage.
I bought a second shelf for storage. it snapped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hans from OGDEN, UT
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this instruction helpful to you?
Thank you for voting!