WRX735SDHZ01 Whirlpool Refrigerator - Instructions

Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.

I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!

The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!

I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

I called the repairman and he troubleshot the problem and told me that he could order the part or that I could. He quickly explained what to do. I ordered the part it came in with 2 days during that time I looked up on how to remove and replace the part on the website. The website stated it took around 15 minutes. That is all it took. I had to use a screw driver to remove two screws and seperate the connection. I reconnected the wiring per instructions on the website reversed the process and it was done within 15 minutes. I save a lot of money and time away from work. This is a grest site to get what you need to fix your appliances. If I have any problems with my other equipment I will becoming back to this website to get the parts and information

I want to thank you for providing the information and helping folks out that can do the job

unscrewed to removed old and screwed in new

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in the pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.

Pull out old module...
Remove 2 wires...
Tape to inside wall [don't want them to fall down into side panel]..

Order new switch..

Fed Ex pkg came on 2nd day..

Install wires on switch...
Press into opening...
Check door light on..[OK]
.. Done

Turned old one until it snapped out. Replaced it with a turn.

Unsnap damper louver cover using only your fingernails at bottom. Remove two phillips screws from damper cover. Remove styrofoam molded insulation. Squeeze electrical connector to release latch; unplug connector. Release latches on both sides of damper control while gently pulling on damper control unit to remove it. Install new unit by doing above steps in reverse. Damper door may move when electrics connected; keep fingers clear.
Amana would not honor our extended warranty that we paid $65 for, saying that noises are not covered. Im glad that Partselect supplied the part quick and and a great price. The frig is quiet for the first time in 2 years!

There is a Philips head screw that holds the light cover on. Remove it. Pull the cover off from the back. It is rather tight so you need to pull fairly hard. Two tabs on the left side of the light hold the assembly in place. Release them and drop the module down. Unplug and do the reverse to put it back together.

The manual says to unplug.the refrigerator. Power to the light can be turned off by taping the door switch down.

Remove cover inside frig at rearwall top with screw driver. Remove phillips screws holding unit in place. Unclip connectors ,and replace in reverse order.