Models
>
RS257BABB
RS257BABB Samsung Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Aug 21
$54.12
This genuine OEM water filter is made for your side-by-side or French door refrigerator, working to reduce impurities like iron, chlorine, and rust for better-tasting water. With a capacity of 300 gal...
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
$30.24
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator...
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
$6.51
This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.
In Stock
Order now and your part arrives by Aug 21
$6.32
This roller wheel axle pin (part number DA61-01920A) is for refrigerators. Roller wheel axle pin DA61-01920A attaches the roller wheel to the roller wheel bracket. Wear work gloves to protect your han...
In Stock
Order now and your part arrives by Aug 21
Common Problems and Symptoms for RS257BABB
Viewing 2 of 2Ice maker not making ice
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ductri from RESEDA, CA
- Parts Used:
- DA63-01809A, DA31-00016A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Refrigeration side was not cold enough.
Replaced the Broken Cover Motor and the Fan Blade. Fan motor was test with 12VDC power supply, or by replugging fan connector and holding down the door closing switch.
After a few days, the fan made loud noise. Due to defrog heater was open when it was test with ohmmeter. Ice deposited around the fan.
I had to buy ... Read more a whole ASSY EVAP-REF part # DA96-00395C, and seperated the evaperator, and replaced the heater and sensor.
Spray bottle was used spray hot water to de-iced the evaperator. And salt accelerated the ice melting process.
Note: spray water to clean salt before installing new parts
After a few days, the fan made loud noise. Due to defrog heater was open when it was test with ohmmeter. Ice deposited around the fan.
I had to buy ... Read more a whole ASSY EVAP-REF part # DA96-00395C, and seperated the evaperator, and replaced the heater and sensor.
Spray bottle was used spray hot water to de-iced the evaperator. And salt accelerated the ice melting process.
Note: spray water to clean salt before installing new parts
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from LAS VEGAS, NV
- Parts Used:
- DA66-00294A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lever Dispenser-Ice Was Broken.
Using the putty knife, pry off the faceplate for the ice/water dispenser. Disconnect the wire harness. Using philips head screwdriver, remove the dispenser assembly. Remove the old dispenser and replace. Reverse for reassembly. Note * I should have bought the water dispenser lever and replaced it as well since I had the assembly out.
... Read more
Secondary note * be mindful during reassembly to not put pressure on the water dispenser or have a glass handy. :)
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from SALISBURY, NC
- Parts Used:
- DA63-02284B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Ice tray had cracked and broken. The water is still not filling up my ice tray.
The replacement was fairly simple. I removed the existing tray and detached the water line. Once the water line water reattached to the new tray I inserted into the ice maker.
*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
Was this instruction helpful to you?
Thank you for voting!