RF28HDEDTSR (AA-0002) Samsung Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from GULFPORT, MS
- Parts Used:
- DA32-10104N
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Evaporator frozen (refrigrator section) and allowing top section to lose cooling
This is the Samsung French door refrigerator style that so many people have complained about freezing up and not cooling the top section. I first changed out the defrost thermostat and this did not correct the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change when holding an ice cube on the sensor so I just assumed it was ok. PLEASE TAKE NOTE: When performing a resistance check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off calibration and was causing the freeze up. Its working as designed now and DW is happy again. Learn from my mistake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max E from MONETT, MO
- Parts Used:
- DA47-00192E
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
lower ice maker water fill tube frozen... suspected that the fill tube heater went bad.
Interestingly, the few authorized samsung parts suppliers I found declared that this model did not have a lower icemaker, whereas this company actually had the specific part. The heater swap is completely straightforward, and simple, but for one detail. The insulation wrap is easily torn when pulling the tube out and my time was spent finding a suitable material to patch the hole. I would recommend purchasing a new tube with heater element and wrap pre-installed. This issue in no way diminished my satisfaction with the product or the prompt delivery time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from BAKERSFIELD, CA
- Parts Used:
- DA97-12625A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
CLOSING MECHANISM BROKE IN TWO.
OPENED THE LEFT SIDE REFRIGERATOR DOOR WHERE THE DEFECTIVE MECHANISM WAS. GOT UP ON THE FIRST STEP OF THE STEP STOOL,REMOVED THE PHILLIPS HEAD RETAINING SCREW FROM THE BROKEN PART.PUT THE NEW CLOSING MECHANISM IN PLACE AND RE-INSTALLED THE PHILLIPS HEAD SCREW. STEPPED DOWN FROM THE STEP STOOL AND SHUT THE REFRIGERATOR DOOR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from HENRICO, VA
- Parts Used:
- DA67-01650A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
A broken siphon break elbow
Partselect made the repair process incredibly easy by linking a how-to video that explained exactly what to do. Without the video, I was trying to take the whole washer apart, but the video noted a convenient opening that provided easy access.
This is my second experience with Partselect, and I am definitely a fan. How you can maintain a stockpile of parts for so many appliances (as well as providing installation guidance for at least some items) is remarkable. Thanks.
This is my second experience with Partselect, and I am definitely a fan. How you can maintain a stockpile of parts for so many appliances (as well as providing installation guidance for at least some items) is remarkable. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HILLIARD, OH
- Parts Used:
- DA61-05435A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
icemaker would not stop making ice
removed the front food tray
removed the broken ice maker shut off arm from the left side of the ice maker using a short Phillips screw driver, very little room between the
ice maker and the side of the fridge.
secured the new ice maker shut off arm with the same Phillips head
screw, the arm self positions via a locating notch
removed the broken ice maker shut off arm from the left side of the ice maker using a short Phillips screw driver, very little room between the
ice maker and the side of the fridge.
secured the new ice maker shut off arm with the same Phillips head
screw, the arm self positions via a locating notch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from MADISON, AL
- Parts Used:
- DA97-12625A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part broke
Took out the screw, removed the broken part, put new part on, put retaining screw back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from FORT WORTH, TX
- Parts Used:
- DA97-14474C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic housing for ice maker cracked preventing the internal mechanism from moving/emptying ice cubes
Since the ice maker was no longer able to empty ice and the problem was a large crack in the plastic housing right near where the internal screw connects to maker (which we were unable to fix with something simple like tape) we simply had to swap out the whole ice maker. It was just the process of pulling the old one out and sliding the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from RALEIGH, NC
- Parts Used:
- DA32-00006R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator was too cold - down to 18 degrees Fahrenheit.
Removed shelves. Removed back cover. Removed old sensor. Installed new sensor. Replaced back cover. Replaced shelves. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from BAKERS MILLS, NY
- Parts Used:
- DA61-03734A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
We misplaced the mounting screws for our handles while moving.
It was easy! I just used an alan wrench to losen the side bolt, then slid the handle into the new mounting screws that I had hand-screwed and then tightened it all up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from SALISBURY, NC
- Parts Used:
- DA63-02284B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Ice tray had cracked and broken. The water is still not filling up my ice tray.
The replacement was fairly simple. I removed the existing tray and detached the water line. Once the water line water reattached to the new tray I inserted into the ice maker.
*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
Was this instruction helpful to you?
Thank you for voting!