Models
>
RF28HMELBSR
RF28HMELBSR (AA-0007) Samsung Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for RF28HMELBSR
Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
In Stock
On Order
$146.61
The ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
In Stock
On Order
In Stock
In Stock
On Order
In Stock
$48.01
If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for RF28HMELBSR
Viewing 5 of 5Fridge too warm
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from GULFPORT, MS
- Parts Used:
- DA32-10104N
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Evaporator frozen (refrigrator section) and allowing top section to lose cooling
This is the Samsung French door refrigerator style that so many people have complained about freezing up and not cooling the top section. I first changed out the defrost thermostat and this did not correct the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change w
... Read more
hen holding an ice cube on the sensor so I just assumed it was ok. PLEASE TAKE NOTE: When performing a resistance check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off calibration and was causing the freeze up. Its working as designed now and DW is happy again. Learn from my mistake.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger Holmgren c/o Lazarus from LAKEWOOD, CO
- Parts Used:
- DA82-02161E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer door was dented. Found a new one at PartSelect.
1) Remove items from freezer.
2) Remove/lift out top slider drawer, and the in door slot tray.
3) Remove lower, large plastic tub/drawer bottom.
4) Remove 6 of the 8 phillips head screws that hold the sliders to the drawer front.
5) Remove while holding up the drawer front with foot, or other spacer to hold up the d ... Read more rawer front when removing the last 2 screws.
6) Pull rubber gasket out of the original drawer front, and press it into the new drawer front.
7) loosen the allen screw from the bottom right side of the handle.
8) slide the handle to the right to remove it from the old door.
9) Slide the handle in place onto the new door, and tighten the allen screw on the bottom right.
10) Place the new drawer front onto the slides. (There are 2 dowel type knobs that locate the drawer front correctly.)
11) Start 1 screw into each slider, making sure that the dowels line up with the holes in the sliders.
12) Install the remaining 6 screws holding the sliders to the drawer front. 13) replace the bottom tub, the slide drawer, and long slot tray.
You're done, other than reloading your frozen items back in the freezer.
2) Remove/lift out top slider drawer, and the in door slot tray.
3) Remove lower, large plastic tub/drawer bottom.
4) Remove 6 of the 8 phillips head screws that hold the sliders to the drawer front.
5) Remove while holding up the drawer front with foot, or other spacer to hold up the d ... Read more rawer front when removing the last 2 screws.
6) Pull rubber gasket out of the original drawer front, and press it into the new drawer front.
7) loosen the allen screw from the bottom right side of the handle.
8) slide the handle to the right to remove it from the old door.
9) Slide the handle in place onto the new door, and tighten the allen screw on the bottom right.
10) Place the new drawer front onto the slides. (There are 2 dowel type knobs that locate the drawer front correctly.)
11) Start 1 screw into each slider, making sure that the dowels line up with the holes in the sliders.
12) Install the remaining 6 screws holding the sliders to the drawer front. 13) replace the bottom tub, the slide drawer, and long slot tray.
You're done, other than reloading your frozen items back in the freezer.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from BAKERSFIELD, CA
- Parts Used:
- DA97-12625A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
CLOSING MECHANISM BROKE IN TWO.
OPENED THE LEFT SIDE REFRIGERATOR DOOR WHERE THE DEFECTIVE MECHANISM WAS. GOT UP ON THE FIRST STEP OF THE STEP STOOL,REMOVED THE PHILLIPS HEAD RETAINING SCREW FROM THE BROKEN PART.PUT THE NEW CLOSING MECHANISM IN PLACE AND RE-INSTALLED THE PHILLIPS HEAD SCREW. STEPPED DOWN FROM THE STEP STOOL AND SHUT THE REFRIGERATOR DOOR.
Was this instruction helpful to you?
Thank you for voting!