Models > RS2577SW

RS2577SW (XAA) Samsung Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for RS2577SW

Viewing 12 of 12
Keep searches simple, eg. "belt" or "pump".
The Samsung Defrost Sensor (DA32-10105R) is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is...
On Order
This genuine OEM water filter is made for your side-by-side or French door refrigerator, working to reduce impurities like iron, chlorine, and rust for better-tasting water. With a capacity of 300 gal...
In Stock
Order now and your part arrives by Jul 5
In Stock
Order now and your part arrives by Jul 5
In Stock
Order now and your part arrives by Jul 5
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator...
In Stock
Order now and your part arrives by Jul 5
In Stock
Order now and your part arrives by Jul 5
In Stock
Order now and your part arrives by Jul 5
In Stock
Order now and your part arrives by Jul 5
$18.65
In Stock
Order now and your part arrives by Jul 5
In Stock
Order now and your part arrives by Jul 5
The ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
On Order
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for RS2577SW

Viewing 1 of 1
Fridge too warm
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from WILMINGTON, DE
Parts Used:
DA32-10105R
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers
Ice Build up behind refrigerator internal panel
I performed the repair to my own refrigerator, after watching multiple YouTube videos. I installed a secondary heater for the defrost coils and replaced the defrost sensor. The defrost sensor was actually bad. Today, 1/27/2024 I rechecked the fix from last week. All seems to be good so far.

If I get any build up of any ice on t he bottom tray of the recessed panel where the drain port is located. I suspect I will also need a new Defrost Heater as well. For now the refrigerator is operating as expected. There is a small amount of ice build up as of today.

Also, I had recently replaced the drain tubes, added a longer heater element part to fit the drain hole, and cleaned the fins in the back of the refrigerator. Thank you.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Belle Fourche, SD
Parts Used:
DA32-10105R
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Fridge side no longer cooled, freezer still workekd fine.
A couple of blogs said the freezer defrost sensor should be replaced, so I ordered one. Did not fix it. I did, however find a service manual online and one of the blog sites and it showed me how to remove the inside duct work. I discovered the fan the recirculates the air across the evaporator coil was not working. Ordered a new fan mo tor and installed it, fridge works perfectly now.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ductri from RESEDA, CA
Parts Used:
DA63-01809A, DA31-00016A
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
Refrigeration side was not cold enough.
Replaced the Broken Cover Motor and the Fan Blade. Fan motor was test with 12VDC power supply, or by replugging fan connector and holding down the door closing switch.

After a few days, the fan made loud noise. Due to defrog heater was open when it was test with ohmmeter. Ice deposited around the fan.

I had to buy a whole ASSY EVAP-REF part # DA96-00395C, and seperated the evaperator, and replaced the heater and sensor.
Spray bottle was used spray hot water to de-iced the evaperator. And salt accelerated the ice melting process.

Note: spray water to clean salt before installing new parts
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!