Models
>
RS265LAWP/XAA
RS265LAWP/XAA Samsung Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$40.90
The Samsung Defrost Sensor (DA32-10105R) is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is...
In Stock
Order now and your part arrives by Oct 1
In Stock
Order now and your part arrives by Oct 1
In Stock
Order now and your part arrives by Oct 1
$30.24
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator...
In Stock
Order now and your part arrives by Oct 1
In Stock
Order now and your part arrives by Oct 1
In Stock
Order now and your part arrives by Oct 1
In Stock
Order now and your part arrives by Oct 1
$6.32
This roller wheel axle pin (part number DA61-01920A) is for refrigerators. Roller wheel axle pin DA61-01920A attaches the roller wheel to the roller wheel bracket. Wear work gloves to protect your han...
In Stock
Order now and your part arrives by Oct 1
In Stock
Order now and your part arrives by Oct 1
$189.47
The ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Special Order
In Stock
Order now and your part arrives by Oct 1
Common Problems and Symptoms for RS265LAWP/XAA
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from WILMINGTON, DE
- Parts Used:
- DA32-10105R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Ice Build up behind refrigerator internal panel
I performed the repair to my own refrigerator, after watching multiple YouTube videos. I installed a secondary heater for the defrost coils and replaced the defrost sensor. The defrost sensor was actually bad. Today, 1/27/2024 I rechecked the fix from last week. All seems to be good so far.
If I get any build up of any ice on t ... Read more he bottom tray of the recessed panel where the drain port is located. I suspect I will also need a new Defrost Heater as well. For now the refrigerator is operating as expected. There is a small amount of ice build up as of today.
Also, I had recently replaced the drain tubes, added a longer heater element part to fit the drain hole, and cleaned the fins in the back of the refrigerator. Thank you.
If I get any build up of any ice on t ... Read more he bottom tray of the recessed panel where the drain port is located. I suspect I will also need a new Defrost Heater as well. For now the refrigerator is operating as expected. There is a small amount of ice build up as of today.
Also, I had recently replaced the drain tubes, added a longer heater element part to fit the drain hole, and cleaned the fins in the back of the refrigerator. Thank you.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Belle Fourche, SD
- Parts Used:
- DA32-10105R
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Fridge side no longer cooled, freezer still workekd fine.
A couple of blogs said the freezer defrost sensor should be replaced, so I ordered one. Did not fix it. I did, however find a service manual online and one of the blog sites and it showed me how to remove the inside duct work. I discovered the fan the recirculates the air across the evaporator coil was not working. Ordered a new fan mo
... Read more
tor and installed it, fridge works perfectly now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from LAS VEGAS, NV
- Parts Used:
- DA66-00294A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lever Dispenser-Ice Was Broken.
Using the putty knife, pry off the faceplate for the ice/water dispenser. Disconnect the wire harness. Using philips head screwdriver, remove the dispenser assembly. Remove the old dispenser and replace. Reverse for reassembly. Note * I should have bought the water dispenser lever and replaced it as well since I had the assembly out.
... Read more
Secondary note * be mindful during reassembly to not put pressure on the water dispenser or have a glass handy. :)
Read less
Was this instruction helpful to you?
Thank you for voting!