Models
>
RFG237AARSXAC
RFG237AARSXAC Samsung Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Nov 12
$143.95
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
$54.12
This genuine OEM water filter is made for your side-by-side or French door refrigerator, working to reduce impurities like iron, chlorine, and rust for better-tasting water. With a capacity of 300 gal...
In Stock
Order now and your part arrives by Nov 12
The door bin attaches to the inside of the refrigerator door and typically holds jars and bottles.
In Stock
Order now and your part arrives by Nov 12
$30.24
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator...
In Stock
Order now and your part arrives by Nov 12
This freezer door handle mounting cap (part number DA67-02056A) is for refrigerators. Freezer door handle mounting cap DA67-02056A helps hold the door handle to the freezer door outer panel. Wear work...
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
On Order
In Stock
Order now and your part arrives by Nov 12
$179.46
Water inlet valve assembly DA97-07827B is an original equipment manufacturer (OEM) part. Water inlet valve assembly DA97-07827B supplies water to the ice maker and water dispenser in the refrigerator....
In Stock
Order now and your part arrives by Nov 12
Common Problems and Symptoms for RFG237AARSXAC
Viewing 3 of 3Door won’t open or close
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- theodore from PUEBLO, CO
- Parts Used:
- DA31-00146E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer was cold fridge was not
Took shelving out of freezer removed panel. Took second panel
out and removed motor. Whole repair took 45 minutes. Works perfect
out and removed motor. Whole repair took 45 minutes. Works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from McGregor, TX
- Parts Used:
- DA97-07602A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old ice bucket was locked up.
Pull old tray out & replace with new tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Chapel Hill, NC
- Parts Used:
- DA67-02056A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right side of freezer door handle broke
This is the older model of the Samsung refrigerator, so there is **no Allen screw underneath the handle** to remove it. That was a change made on newer models.
To replace the broken freezer handle cap:
1. **Remove the gray top cover.** Slide the gray cover forward, then lift it up and off.
2. **Remove the ... Read more two Phillips screws** underneath the cover.
3. **Remove the front tabs.** Gently pry the front of the tabs forward. Using needle-nose pliers, carefully pull the tabs out.
4. **Remove the broken cap.** Once the tabs are removed, the broken cap can be taken off.
5. **Remove the handle from the old cap.** In my case, the handle had broken away from the old cap. There are two Phillips screws securing the handle to the cap. Remove those screws and separate the handle from the old cap.
6. **Reuse the silver hinge pin.** Before discarding the old cap, remove the silver rod/hinge pin by sliding it out. You will reuse this pin in the new cap. If necessary, apply a small amount of light lubricant to help it slide out and back in.
7. **Attach the handle to the new cap.** Use the two Phillips screws to attach your existing freezer handle to the new cap.
8. **Install the new cap and handle.** Position the new cap and handle assembly on the freezer door. This part is a little fiddly, so be patient and make sure everything is properly aligned before tightening anything.
9. **Reinstall the two tabs.** Put the tabs back into position and secure them with the two Phillips screws.
10. **Replace the gray cover.** Snap the gray cover back over the new cap.
That's it. The key difference with this older Samsung model is that **you do not remove the handle with an Allen screw**. The handle is secured to the cap with two Phillips screws, and the silver hinge pin from the original cap is reused in the replacement cap.
To replace the broken freezer handle cap:
1. **Remove the gray top cover.** Slide the gray cover forward, then lift it up and off.
2. **Remove the ... Read more two Phillips screws** underneath the cover.
3. **Remove the front tabs.** Gently pry the front of the tabs forward. Using needle-nose pliers, carefully pull the tabs out.
4. **Remove the broken cap.** Once the tabs are removed, the broken cap can be taken off.
5. **Remove the handle from the old cap.** In my case, the handle had broken away from the old cap. There are two Phillips screws securing the handle to the cap. Remove those screws and separate the handle from the old cap.
6. **Reuse the silver hinge pin.** Before discarding the old cap, remove the silver rod/hinge pin by sliding it out. You will reuse this pin in the new cap. If necessary, apply a small amount of light lubricant to help it slide out and back in.
7. **Attach the handle to the new cap.** Use the two Phillips screws to attach your existing freezer handle to the new cap.
8. **Install the new cap and handle.** Position the new cap and handle assembly on the freezer door. This part is a little fiddly, so be patient and make sure everything is properly aligned before tightening anything.
9. **Reinstall the two tabs.** Put the tabs back into position and secure them with the two Phillips screws.
10. **Replace the gray cover.** Snap the gray cover back over the new cap.
That's it. The key difference with this older Samsung model is that **you do not remove the handle with an Allen screw**. The handle is secured to the cap with two Phillips screws, and the silver hinge pin from the original cap is reused in the replacement cap.
Read less
Was this instruction helpful to you?
Thank you for voting!