RS2521SWXAA Samsung Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Hudson, WI
- Parts Used:
- DA31-00103A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Condensor fan was not functioning propperly
Unplugged Unit
Removed back cover
removed fan assembly
removed fan balde
opened motor case
replaced motor
sealed the motor case
fastened to fan shroud
re installed fan blade
re attacehd to frig- Carefull of the coolant lines
Plugged in motor assembly
Replaced back cover
Re Plugged in Frig to AC outlet.
Removed back cover
removed fan assembly
removed fan balde
opened motor case
replaced motor
sealed the motor case
fastened to fan shroud
re installed fan blade
re attacehd to frig- Carefull of the coolant lines
Plugged in motor assembly
Replaced back cover
Re Plugged in Frig to AC outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Tucson, AZ
- Parts Used:
- DA97-02203G
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker not functioning properly
Barely losened the two rear screws. Took out the two front screws and the ice maker slides toward front of fridge off the 2 rear screws. Unhooked the wiring plug. Replaced with new ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Newtown Square, PA
- Parts Used:
- DA31-00103A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stripe down ctr of side by side refrigerator
unplugged first, then Pulled out frig and took out fan motor. plugged in to be sure it worked. waited few minutes and it started running. then placed everything back where it belonged. Talked to appliance store and told me what the problem was but it would take longer for them to get then for me to order on line. Best way to get it done... No directions on box...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from LAS VEGAS, NV
- Parts Used:
- DA66-00294A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lever Dispenser-Ice Was Broken.
Using the putty knife, pry off the faceplate for the ice/water dispenser. Disconnect the wire harness. Using philips head screwdriver, remove the dispenser assembly. Remove the old dispenser and replace. Reverse for reassembly. Note * I should have bought the water dispenser lever and replaced it as well since I had the assembly out. Secondary note * be mindful during reassembly to not put pressure on the water dispenser or have a glass handy. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from SALISBURY, NC
- Parts Used:
- DA63-02284B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Ice tray had cracked and broken. The water is still not filling up my ice tray.
The replacement was fairly simple. I removed the existing tray and detached the water line. Once the water line water reattached to the new tray I inserted into the ice maker.
*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
Was this instruction helpful to you?
Thank you for voting!