RFG295ABBPXAA Samsung Refrigerator - Instructions

Unscrewed 1 screw, removed panel, disconnected old icemaker and removed it, Added new icemaker, reconnected, replaced panel, replaced screw, & reset new icemaker. Started making ice almost immediately. Threw out entire first load of ice. Working great since! I wasn’t sure if it was the icemaker or the water valve to it so had a guy come out ($50) who confirmed it was the icemaker. He wanted $550 to replace it (part/labor). We bought the part here at Part Select for $185 (part/tax/delivery) and saved $265 on a job that took less than 15 minutes.

Took shelving out of freezer removed panel. Took second panel
out and removed motor. Whole repair took 45 minutes. Works perfect

Once I understand how to remove the old part the rest was very easy .
Had ice in a couple of hours .

Went on the Internet to find the installation instructions.

YouTube the video on how to replace the ice maker. Unplugged the fridge, one screw was removed to open a small cover panel to access where the ice maker was plugged in, unplugged the ice maker, pushed a small locking clip and pulled the old ice maker off the keyhole slots holding it in place removing it from the fridge. Did the steps in reverse and reinstalled the new one. Plugged the fridge back in and reset the fridge by holding the energy saver and alarm button on the front door simultaneously for 8-10 seconds until it beeped. Took a few seconds and the fridge reset

I am 70 and identified the problem and ordered the part. I watched a video lots of times that showed how to... slowing it down to catch details.
It is very easy... and the only problem was that when you are trying to get the assembly out you need a lot of hand strenght that I don't have.
My son easily wriggled and loosened it and out it came. Plug in the wires and pop the new unit in.
Two hours later I heard the delightful sound of ice dropping into the bucket and amazingly the bottom freezer started making ice too!
There is no mention that they are related but it did. We thought the freezer sensor had died but it all works!

You can do it! Best, pb

Prepare the area
Open the refrigerator door(s). Remove the ice bucket/bin by lifting it up and pulling it out (it usually slides forward after a slight lift). Set it aside. Empty any loose ice.
Remove the ice maker cover / upper panel (if present)
There is often a plastic cover or shroud over or in front of the ice maker. Gently pull or pry it off using a flathead screwdriver on the release tabs. Some models have screws holding this cover. Note the orientation for reassembly.
Disconnect the wiring harness
Locate the electrical connector (usually a 12-pin plug) on the side or back of the ice maker.
Press the release tab on the connector and gently pull it apart. Do not yank the wires. Tuck the harness aside safely.
Remove the mounting screws
There are typically 2 screws (Phillips) securing the ice maker to the refrigerator wall or bracket — one on the side/top and possibly another. Support the ice maker with one hand while removing the screws so it doesn’t drop.

Remove the old ice maker
Carefully tilt and pull the unit forward/out. It may have tabs or hooks that need to be released. Wiggle gently if stuck. Avoid forcing it to prevent breaking plastic parts or damaging the fill tube.

Install the new ice maker (DA97-07365G)
Position the new assembly in the same orientation. Align any tabs, hooks, or slots with the mounting bracket.
Reinstall the 2 mounting screws snugly (do not overtighten).
Reconnect the wiring harness firmly until it clicks.
Reassemble the cover/panel
Snap or screw the cover back into place.

Reinstall the ice bucket
Slide the ice bin back in until it seats properly.

Power on and test
Plug the refrigerator back in.
The ice maker may take time to cool down and begin a cycle (several hours).
Press the Test/Reset button on the ice maker (small button on the side or front of the unit) to run a test cycle if available. You should hear the motor and eventually a fill.
Check the control panel on the door — ensure Ice Maker is turned On (not Ice Off).
Monitor for the first batch of ice (can take 6–24 hours depending on temperature and usage).

Took out Philip’s screw. Applied heat from hand hair dryer for one minute. Unplugged wire plug. Pushed ice maker lever to release and gently pulled forward.Removed old ice maker and replaced with a new maker.
Plugged in wire harness and replaced wire cover.

Slide the old door bin out. Put the new door bin in. That easy! Fits perfectly!

The description at the website was excellent so I was confident I was ordering the correct replacement bin. And it slid right in with no problems.

(1) Set ice production to OFF from the front panel of the refridgerator. (2) Inside the fridge, remove the screw holding the panel covering the cable for the ice naker assembly. (3) Remove the panel. (4) Disconnect the power cable of ice maker. (5) Holding the assembly with one hand, release the locking clip of assembly housing, and slide assembly forward until it is free. (6) Remove the ice maker assembly. (7) Install the new assembly by reversing the previous steps. (8) Reset the ice maker by pressing the reset button and holding it for at least 8 seconds. The first time the ice maker is primed with water, there are 2 chimes. (1 High , 1 Low).