Models
>
RF263AERSXAC
RF263AERSXAC Samsung Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
On Order
$146.66
This door gasket creates a seal around the door to prevent warm air from entering the refrigerator and are sold individually.
In Stock
Order now and your part arrives by Nov 12
$198.90
This is a 40W/120V ice maker assembly for your refrigerator. Ice maker assemblies are designed to continuously make ice cubes by supplying water through its valve, freezing it, and then ejecting the c...
On Order
In Stock
Order now and your part arrives by Nov 12
$54.12
This genuine OEM water filter is made for your side-by-side or French door refrigerator, working to reduce impurities like iron, chlorine, and rust for better-tasting water. With a capacity of 300 gal...
In Stock
Order now and your part arrives by Nov 12
This freezer door handle mounting cap (part number DA67-02056A) is for refrigerators. Freezer door handle mounting cap DA67-02056A helps hold the door handle to the freezer door outer panel. Wear work...
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
On Order
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
Common Problems and Symptoms for RF263AERSXAC
Viewing 4 of 4Ice maker not making ice
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lyndi from LEBANON, TN
- Parts Used:
- DA63-06542A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator was freezing food on the bottom shelves
It was simple. I pulled out the old seal from the track it was tucked in and put the new one in using a wood spatula to help along the folding part of the door that fits behind the other door. I replaced both seals under 15 minutes. I am a 63 year old female so I know if I can do it so can you!
Tip: make sure that you line up the to ... Read more p and bottom and from side to side evenly before you start pressing it into the track.
Refrigerator is working properly now.
Tip: make sure that you line up the to ... Read more p and bottom and from side to side evenly before you start pressing it into the track.
Refrigerator is working properly now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Chapel Hill, NC
- Parts Used:
- DA67-02056A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right side of freezer door handle broke
This is the older model of the Samsung refrigerator, so there is **no Allen screw underneath the handle** to remove it. That was a change made on newer models.
To replace the broken freezer handle cap:
1. **Remove the gray top cover.** Slide the gray cover forward, then lift it up and off.
2. **Remove the ... Read more two Phillips screws** underneath the cover.
3. **Remove the front tabs.** Gently pry the front of the tabs forward. Using needle-nose pliers, carefully pull the tabs out.
4. **Remove the broken cap.** Once the tabs are removed, the broken cap can be taken off.
5. **Remove the handle from the old cap.** In my case, the handle had broken away from the old cap. There are two Phillips screws securing the handle to the cap. Remove those screws and separate the handle from the old cap.
6. **Reuse the silver hinge pin.** Before discarding the old cap, remove the silver rod/hinge pin by sliding it out. You will reuse this pin in the new cap. If necessary, apply a small amount of light lubricant to help it slide out and back in.
7. **Attach the handle to the new cap.** Use the two Phillips screws to attach your existing freezer handle to the new cap.
8. **Install the new cap and handle.** Position the new cap and handle assembly on the freezer door. This part is a little fiddly, so be patient and make sure everything is properly aligned before tightening anything.
9. **Reinstall the two tabs.** Put the tabs back into position and secure them with the two Phillips screws.
10. **Replace the gray cover.** Snap the gray cover back over the new cap.
That's it. The key difference with this older Samsung model is that **you do not remove the handle with an Allen screw**. The handle is secured to the cap with two Phillips screws, and the silver hinge pin from the original cap is reused in the replacement cap.
To replace the broken freezer handle cap:
1. **Remove the gray top cover.** Slide the gray cover forward, then lift it up and off.
2. **Remove the ... Read more two Phillips screws** underneath the cover.
3. **Remove the front tabs.** Gently pry the front of the tabs forward. Using needle-nose pliers, carefully pull the tabs out.
4. **Remove the broken cap.** Once the tabs are removed, the broken cap can be taken off.
5. **Remove the handle from the old cap.** In my case, the handle had broken away from the old cap. There are two Phillips screws securing the handle to the cap. Remove those screws and separate the handle from the old cap.
6. **Reuse the silver hinge pin.** Before discarding the old cap, remove the silver rod/hinge pin by sliding it out. You will reuse this pin in the new cap. If necessary, apply a small amount of light lubricant to help it slide out and back in.
7. **Attach the handle to the new cap.** Use the two Phillips screws to attach your existing freezer handle to the new cap.
8. **Install the new cap and handle.** Position the new cap and handle assembly on the freezer door. This part is a little fiddly, so be patient and make sure everything is properly aligned before tightening anything.
9. **Reinstall the two tabs.** Put the tabs back into position and secure them with the two Phillips screws.
10. **Replace the gray cover.** Snap the gray cover back over the new cap.
That's it. The key difference with this older Samsung model is that **you do not remove the handle with an Allen screw**. The handle is secured to the cap with two Phillips screws, and the silver hinge pin from the original cap is reused in the replacement cap.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from SAUTEE, GA
- Parts Used:
- DA67-02057A, DA67-02056A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Installed caps on broken lower handle
Unscrewed broken caps and installed new ones
Was this instruction helpful to you?
Thank you for voting!