MFI2269DRE01 Maytag Refrigerator - Instructions

Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.

A very easy fix took all of five minutes

I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!

The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!

I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

unscrewed to removed old and screwed in new

Please note I had to remove the complete old wire harness from and install the new proper one as my part number was replaced with a new part number. The new ice maker repair kit comes with 2 new harnesses each slightly different one for a 22 cubic foot model the other for the 25cf model. It looks intimidating initially, just take pictures FIRST BEFORE removing old harness to see all the connections. I was surprised this was necessary but it is, as the 'H" pin on the front of the new ice maker motor was different from my old one. Would have only taken me 15 minutes or so to replace the old ice maker but with having to remove the old harness and re-route the new harness it will take you a bit of time and patience but you can do it. Another note you will have to remove the Electromagnet to get to the green grounding screw on the ice maker itself. There are good videos on Part Select and youtube showing how to remove the ice maker itself, but did not find one on the wire harness, like I said just take lots of good pictures showing all the connection points on the old harness and take your time. It was not too hard. And now I have ice again!

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

removed old rail,lifted glass panel above and inserted new rail-voila!!done.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

The frig. no longer cool downed or operated at all as the electronic control panel was dead. Pulled old part off and put in new part, following instructions on You Tube. However, this part did not solve the issue. I had to call a repairman. The repairman said that another part was needed also, this part costs over $400.00 but, the part was no longer available. I had to purchase a new frig. and not a happy camper to have a 6 year old frig,that a part is no longer available.

Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist both ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.

Turned old one until it snapped out. Replaced it with a turn.