Models
>
GT1781NKCW
GT1781NKCW Maytag Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GT1781NKCW
Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
$18.54
This is an end cap for the shelf retainer bar on your fridge door. This genuine OEM part is white in color and made of plastic. The end cap can be used for either the left or right side of the retaine...
In Stock
Order now and your part arrives by Apr 25
In Stock
Order now and your part arrives by Apr 25
$53.58
This refrigerator door shelf trim is approximately 28 inches long. It is all white in color, and it is made entirely of metal. NOTE: The image may not be of the exact product but will function properly.
In Stock
Order now and your part arrives by Apr 25
In Stock
Order now and your part arrives by Apr 25
$119.70
This defrost timer will cycle for twenty-one minutes after every ten hours of run time.
The defrost timer acts like a clock. It continually advances and alternates between activating the cooling cy...
In Stock
Order now and your part arrives by Apr 25
In Stock
Order now and your part arrives by Apr 25
$37.49
This lower hinge pin is just over an inch long. It is black in color and is made of plastic. It is located on the bottom part of the door hinge.
In Stock
Order now and your part arrives by Apr 25
$13.07
This hinge washer is an inch in diameter. It is all black in color and is made of plastic. Sold individually.
In Stock
Order now and your part arrives by Apr 25
This clear fresh food control knob is almost three inches in diameter. There is blue numbering around the perimeter of the knob denoting the level of coldness inside the refrigerator.
In Stock
Order now and your part arrives by Apr 25
This evaporator fan motor assembly is just over three inches long. It is made of both metal and plastic, and is made up of black, white, and metalllic pieces.
In Stock
Order now and your part arrives by Apr 25
In Stock
Order now and your part arrives by Apr 25
$7.60
This screw is less than an inch long, and is made entirely of metal. Sold individually.
In Stock
Order now and your part arrives by Apr 25
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GT1781NKCW
Viewing 8 of 8Light not working
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Fridge too cold
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clint from Rayville, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights inside refrigerator not working
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon from Chaparral, NM
- Parts Used:
- WP68233-3
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Would not exit defrost mode (continual defrost)
Unplug the refrigerator. Remove face plate located in the upper back of the refrigerator compartment. Remove face place bracket on the right using nut driver. Removing these screws also frees the metal case enclosing the Defrost Timer. Pull the case away from the back of the refrigerator exposing the Defrost timer. Remove the electri
... Read more
cal plug from the Defrost Timer. Then remove the Defrost Timer from the case by removing the two screws securing it. Reverse the procedure to install the new Defrost Timer.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James Richard from St. Cloud, MN
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Light Switch broke
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only
... Read more
swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Read less
Was this instruction helpful to you?
Thank you for voting!