Models
>
CTL1511GEW
CTL1511GEW Magic Chef Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CTL1511GEW
Viewing 13 of 13
Manuals & Guides for CTL1511GEW
Click to downloadKeep searches simple, eg. "belt" or "pump".
$11.73
This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and uns...
In Stock
$10.69
This is an end cap for the shelf retainer bar on your fridge door. This genuine OEM part is white in color and made of plastic. The end cap can be used for either the left or right side of the retaine...
In Stock
In Stock
$54.77
This refrigerator door shelf trim is approximately 28 inches long. It is all white in color, and it is made entirely of metal. NOTE: The image may not be of the exact product but will function properly.
In Stock
This part allows the refrigerator to go into defrost mode only when required.
No Longer Available
$20.79
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$66.72
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
In Stock
$122.80
This defrost timer will cycle for twenty-one minutes after every ten hours of run time.
The defrost timer acts like a clock. It continually advances and alternates between activating the cooling cy...
In Stock
In Stock
In Stock
$14.53
This hinge washer is an inch in diameter. It is all black in color and is made of plastic. Sold individually.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CTL1511GEW
Viewing 14 of 14Light not working
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
How to fix it
Fridge too cold
Fixed by these parts
How to fix it
Clicking sound
Fixed by these parts
How to fix it
Fridge runs too long
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Freezer too cold
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- james from livermore, CA
- Parts Used:
- 61005988
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Fridge Side Warm Freezer Fine
Removed the Hex head small screw at the middle back of the Back wall of the fridge above the top shelf. Removed the 2 small Hex Head screws that go into the of the Plastic cover upwards into the top roof of the fridge.
I ended up with an extra screw so I dont know what I did...
The hard part is pushing up on the two tabs, one on ... Read more each side in the extreme back on the bottom of that white plastic cover. You have to pull the coverwhile releasing the tab (locks) by pushing UP. The Right side was easier, I got that side to release and drop down. But the left side took some pressure on the tab with a fat screwdriver.
Then you have to kinda of Bend the cover to get it to slide out...
Then take out the 2 phillips screws above the light bulbs. the left side one is tricky, need long skinny driver.
Drop assembly down and on the back right is the ADP board. Mine was a bare board but the replacements are enclosed in white plastic that fit in place just fine.
Pry connector off of the board carefully and drop new plastic circuit board case in and replace.
Put a thermometer in a glass of water. unplug fridge for 10 minutes and then plug it in. Give it a few hours..
Everything seems fine.
A steady 39 degrees with the Fridge control at a few ticks right of middle.
I have no idea what it was before my troubles...
But 36 - 41 seems to be what you need.
I ended up with an extra screw so I dont know what I did...
The hard part is pushing up on the two tabs, one on ... Read more each side in the extreme back on the bottom of that white plastic cover. You have to pull the coverwhile releasing the tab (locks) by pushing UP. The Right side was easier, I got that side to release and drop down. But the left side took some pressure on the tab with a fat screwdriver.
Then you have to kinda of Bend the cover to get it to slide out...
Then take out the 2 phillips screws above the light bulbs. the left side one is tricky, need long skinny driver.
Drop assembly down and on the back right is the ADP board. Mine was a bare board but the replacements are enclosed in white plastic that fit in place just fine.
Pry connector off of the board carefully and drop new plastic circuit board case in and replace.
Put a thermometer in a glass of water. unplug fridge for 10 minutes and then plug it in. Give it a few hours..
Everything seems fine.
A steady 39 degrees with the Fridge control at a few ticks right of middle.
I have no idea what it was before my troubles...
But 36 - 41 seems to be what you need.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Rayville, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights inside refrigerator not working
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Concord, NH
- Parts Used:
- 12002782
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fridge would run but not blow cold air. Compressor would cycle for 12 seconds every 5 minutes
remove back lower panel using nutdriver. Locate and remove Relay and Overload parts from side of Compressor which were located inside a small white box shaped cover unti held on by a spring clip. Attach new Relay and overload to 3 pin terminals on side of compressor. Attach 1 white & 1 orange/white wire to relay terminals. Attach supplied
... Read more
white jumper wire to Overload and other end to Blue wire. Instal new cover supplied with kit replacing old box type cover.
Read less
Was this instruction helpful to you?
Thank you for voting!