LFD25860TT (ATICLGA) LG Refrigerator - Instructions

Remove water filter and water filter holder. Removed cover on back of frig. Removed clip where water line connects to back of water filter. Took half inch wrench pushed in on water line lock to release line. Repeat at other end. Reverse steps to put on new line. Easy repair.

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have continuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.

Ordered a new tank assembly, but the new part also leaked because it had a hole in it. Ordered another that worked fine. Used a flat head screwdriver to remove the clips covering the screw holes to the tank assembly cover, then a phillips to remove the cover screws and the screws retaining the tank. Did not use the tubing that came with the new tank (removed it by taking out the neck clip then simultaneously pushing back on the neck piece while pulling out the hose). Used this same procedure to remove the old tank at both positions. Installed the new tank, replaced the clips, pressurized/tested the system and put the cover back on. Overall less than a 5 minute job...except for the extra week waiting for a good part.

Lower shelf frame lifted right off w/o the use of any tools. Removed both drawer cover fronts.The glass shelf which sits on top of frame over time will tend to stick to shelf frame. Running Hot water over glass dissolved stickiness and glass separated easily.Do Not try and pry apart if it seems stuck to shelf frame!. It may crack!. Cleaned all parts, and replaced both drawer front covers. Put shelf frame back in on shelf holder. Done. Approx.20 minute repair w/o any problems.

Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!

The replacement was the exact size,easy installation.

Pretty simple fix.

1) Removed the screws from lower back plate
2) Removed the screws holding the plastic water lines in place (little plastic brackets - several of them)
3) Take a picture of how the tubing and what hose goes into what part - the 5/16" hose can go into 2 different spots - I didn't do this and I had to fix this
4) Pull out the hose "tabs" that lock the clamp into place (several)
5) Push in new hose
6) Put in clamp
7) I had to remove the filter on the inside of the fridge. Remove the filter, there is one screw that comes out, then you will have access to the hose clamps
8) Repeat for all the other hoses
9) Put the plate and brackets back into place (the picture really helps on how to orient and route the 3 different tubes
10) Test the water
11) Crack open a beer for a job well done

Super easy - take a picture! It will save you time!

An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders Lay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.

As per utube

Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping.
Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minutes.

Be sure to keep all the parts from the old frame because, first, you have to attach the metal stiffener/support bar from the old to the new. Care is necessary trying to fit the upper pop-up drawer doors and the clear plastic drawer tops to the frame. The hinges of the door top are plastic and could break, causing you to have order another part. The clear plastic tops, under the glass the shelf, do not fit intuitively and you have to make sure they fit in the right direction. Along one edge is a 1" square spot; that goes to the back of the frame. Then, you need to be careful snapping them into place so you don't break the supports. Once you have all the parts on in the right places, then it's just a matter of sliding everything into place in the refrigerator.

The replacement part came in a timely manner and snapped right into place.

Compress the ends. It snaps in

Remove the crisper drawer for room to work, locate the two mounting holes at the top, front of the shelf, insert the plastic hinge pin on the outside wall side. Holding the front(cover0 in one hand, reach under the cover with your other hand, grasp the second hinge pin and move it to the insert position. Using your index finger, carefully bend the bracket arm to allow the pin to be inserted.