GR-X308LSJM (ASTCNA1) LG Refrigerator - Instructions

Before you begin, I'd recommend unplugging the refrigerator. You have to slip the putty knife in around the edge of the dispenser panel and carefully release the tabs all the way around and the entire panel pulls straight out. There are three wiring harnesses to unplug. You'll have to remove several screws and release the tabs around the electronic panel and remove it from the main panel. It's a good idea to take note or even pictures of how the ice and water actuators are positioned on the panel, so you get them situated properly on the new panel. If the ice actuator is not fit correctly on a knob that sticks up it may dispense ice all the time (happened to me). After you transfer the actuators to the new panel and the ice and water dispensing levers, you can re-attach the electronic panel on the left side. make sure all of the wiring harnesses are plugged in and the wires situated out of the way, then re-install the panel by pushing it straight back in. Plug the refrigerator in and test it out.

Watch YouTube videos on this topic if you are uncertain before tackling the job. The right door was easy to replace. Just pull the gasket with your fingers and it will come off easily. Place new gasket over door and use fingers to press it inside the groove few inches at a time. Pay attention to gasket orientation.

The left door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.

Could not believe how easy it was!

Installed new door stopper with screw driver on bottom of french door

For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.

For the left side, needed a Phillip’s screwdriver to remove the flap first. Helps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.

Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.

Fortunately, others had left comments about this installation, so proved very helpful. First thing was laying out the gasket flag on the counter to allow it to unbend, get out the kinks from shipping. While the new gasket was laying out on the counter, started removing the old gasket. As it had been there for 11 years, needed pliers to get a corner started. I was slow and careful removing the old gasket in case I needed to put it back in. A very helpful suggestion from others was to lightly rub dishwashing soap on the gasket edge that fits in the groove in the door. Again, slow and careful, got it installed, wiped off any excess dishwashing liquid, and the door closed with a better seal in a long time. Pleasantly surprised how easy this was to do!

Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

Watched a couple of YouTube videos and then went at it

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

easy repair. First step is you need to remove all food from bottom shelf and remove all three produce drawers. Then remove the meat drawer. You will need to lift the bottom self off the rail to remove. It is not heavy and does not need to be fully taken out of fridge - easier if you do but some what hard to get out.Unscrew the rail and unplug the old rail. Clean off the fridge - my fridge was gross behind the rail. Insert the rail into the fridge and then screw in the two screws. Place the bottom self back on the two rails and you are done.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.

Slid the replacement shelves into place.

Phillips head screw driver required.

Door stopper attaches to door and front side of refrigerator. Located at the underside of the door at the front of the hinge.

Remove screw, keep screw for installation of new stopper. Remove damaged stopper, install new stopper using the original screw.

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.