Models
>
LRSC20911TT
LRSC20911TT LG Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for LRSC20911TT
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
$25.10
If the light inside your fridge is not coming on, or if it is staying on continuously, there may be an issue with your door switch. When the door to your fridge is closed, the button on the switch is...
In Stock
Order now and your part arrives by Aug 31
In Stock
Order now and your part arrives by Aug 31
In Stock
Order now and your part arrives by Aug 31
$32.12
This fan assembly circulates air to support cooling or ventilation functions. Designed for reliable airflow, it helps maintain consistent temperatures and efficient operation.
In Stock
Order now and your part arrives by Aug 31
On Order
In Stock
Order now and your part arrives by Aug 31
$94.45
This evaporator fan motor is a replacement drive component designed to circulate air across cooling surfaces. It supports even temperature distribution and is commonly replaced when airflow decreases ...
In Stock
Order now and your part arrives by Aug 31
In Stock
Order now and your part arrives by Aug 31
In Stock
Order now and your part arrives by Aug 31
Common Problems and Symptoms for LRSC20911TT
Viewing 3 of 3Light not working
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Debbie from Waltham, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Remove and replace light switch
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from WOODBURY, MN
- Parts Used:
- 5040JA2009B, 4681JB1029A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Evaporator Fan Squeeking
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin
... Read more
. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from GALLOWAY, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light would not come on.
After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it p
... Read more
opped out, you may need to use pliers to disconnect the switch.
Read less
Was this instruction helpful to you?
Thank you for voting!