GML277USRL (ASTCLGA) LG Refrigerator - Instructions

Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!

Examined old ice maker. It is held by some Philips screws. There are many screws you don't need to unscrew so look carefully. Then disconnected th dual in line connector. There is a little push tab to squeeze to release. Then the ground is connected with a screw. It's a little hard to see but unscrew that. My replacement came with no instructions or screws so try not to drop the screws down in the netherlands of the fridge. The hardest part was maneuvering the icemaker to reattach the power and ground. Even with that pretty straight forward replacement.

The replacement gasket does not have as strong a magnet as the original one. I removed the old one carefully so as not to cause more damage in case I have to put it back. Using Tongue suppressor I pushed new gasket into place and put a thin coating of protelem jelly on the gasket. I just have to make sure the door is closed each time to be sure of good seal.

1. Remove the filter - 1 screw at top of filter and pull-out. 2. Use crescent wrench to push down at tube inlet and pull tube out. 3. Remove bottom screen from refrigerator. 4. Use crescent wrench to push down on water inlet and pull out tube. 5. Route new line on back of refrigerator. 6. Install is the reverse of removal. Thanks.

Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who
knew how to fix my drawer
and they had the part.

Ordered part from part select. Received part with out instructions. It took only one screwdriver for 1 screw removal and then removing cover to replace switch. Pretty simple

Really Easy

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the water line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Replaced water pump assembly, all compression fittings easy to put together

Took off door per normal instructions.
Removed the old stopper and hinge assembly (the hard rubbery parts had worn enough against each other to cause the annoying sound when opening and closing the door).
Inserted the new stopper and hinge assembly.
There was no locking nut on the newer part, so just had to level the fridge door without that part of the instructions (from normal LG instructions)
Overall easy for a non-handy person and the annoying sound is gone.
Wife is happier now.

I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!

Removed old part very easily and installed the new part without any problems. Used and adjustable wrench and screwdriver

replaced gaskets for the second time in four years

removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!

So easy that my 13 years old son replaced it.