LFXS26973S (00) LG Refrigerator - Instructions

Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.

Had to buy the entire door mullion because the spring broke, wasn't happy. Got the new part very quickly and it was a new replacement part number. Somewhat tentative. Took it out of the box and looked it over. No spring! Groan! Thought I got the wrong part. Flipped the bottom hinge and it snapped open, no need for a spring! Two screws, disconnect the wire harness, throw away the old, get new, connect the wire harness, connect hinges, put in two screws! Super easy. Watch the video for some pointers along the way.

Unplug the refrigerator and empty the freezer. Remove the lower basket and roll out upper tray. Open the freezer door. I was able to lie on the floor to remove the 2 screws holding the ice maker without removing the
freezer door. Depress the 2 tabs and slide the ice maker forward to remove. Install in reverse order. Change the water inlet valve at the same time.

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

Removed old bucket and placed new one In its place. New one is actually better than OEM part because it has an arm than breaks up any ice that may jam.

Watched a YouTube video on how to replace the door flipper (mullion). Very easy to unscrew the plate and disconnect the electrical circuit. Then gently slide up the flipper and replace with a new one.

The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.

This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!

Found the part on Parts Select. Ordered the part, which came quickly. While waiting for delivery. I watched a short video on how to replace this part. I'm a 73 yr. old female, and no trouble at all. I really felt a sense of accomplishment. Thank you Parts Select.

Replaced with new mullion

Took off cover, then removed the 8 connector bundles. then removed the the board pulling 3 clips. Replaced board and connected wires. Waiting to see if that fixed it. Replaced freezer fan, Ice maker fan.

Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Installed new one.

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.