74073 (ASTCSE0) LG Refrigerator - Instructions

For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours before you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.

Watch YouTube videos on this topic if you are uncertain before tackling the job. The right door was easy to replace. Just pull the gasket with your fingers and it will come off easily. Place new gasket over door and use fingers to press it inside the groove few inches at a time. Pay attention to gasket orientation.

The left door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.

Could not believe how easy it was!

Installed new door stopper with screw driver on bottom of french door

For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.

For the left side, needed a Phillip’s screwdriver to remove the flap first. Helps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.

Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.

Fortunately, others had left comments about this installation, so proved very helpful. First thing was laying out the gasket flag on the counter to allow it to unbend, get out the kinks from shipping. While the new gasket was laying out on the counter, started removing the old gasket. As it had been there for 11 years, needed pliers to get a corner started. I was slow and careful removing the old gasket in case I needed to put it back in. A very helpful suggestion from others was to lightly rub dishwashing soap on the gasket edge that fits in the groove in the door. Again, slow and careful, got it installed, wiped off any excess dishwashing liquid, and the door closed with a better seal in a long time. Pleasantly surprised how easy this was to do!

Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom.
Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

Watched a couple of YouTube videos and then went at it

Remove 3 screws bottom and base.
Loosen top screw. Pull out from bottome and unplug wire harness.

Very easy. Just slipped it back into place

Removed screws from broken Multi Ducts, pulled broken pieces from ice maker and replaced new Multi Ducts.

I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.

I started by emptying the food out of the refrigerator. Because of the placement of the refrigerator, it was hard for me to open the doors all the way, but I managed to remove the vegetable drawer, the fruit drawer, the deli drawer drawer, and glass that goes in the tray. Once that happened, I realized my refrigerator was a biology experiment in progress.
Using my steam cleaner, I cleaned everything that I could and the refrigerator actually looked almost brand new.
I removed the deli tray to have more room to get the whole tray and side guides . Once you do that. the tray is actually very easy to replace. The guides were still in pretty good condition although I ordered one more because it did have a small crack and eventually it will break.
You remove the three guides (left, right, and center) from the old tray and attach the new tray fram.
Sounds Easy, right?
It takes a bit of finagling because " the magic tray" which is part of the vegitable drawer has to be placed before you put the right guide on. this process is a bit awkward. if you can get an extra hand, it helps. After that, it was very easy to just put things back and I took this opportunity to clean the rest of my refrigerator and re-organize. I am going have to do this again because I have to replace the right guide, which has a crack, but so far it's working great it is not a problem. Nothing that a little duct tape can't solve until the real thing comes along. This project took longer than I thought it would. But that was primarily because I also cleaned the refrigerator, and put the right guide on before I figured out I had to put the humidifier cover in first. I think that's really the key step here.
I leave you with this: I researched how to find these parts and this site t was great. I can replace all of the hardware that breaks in my refrigerator for less than it costs to buy a new refrigerator. My friend felt I should just dump the refrigerator and start new. As other DIY people, that was like fingernails on a chalkboard for me. It's wasteful to the environment and economically unfeasible. So celebrate your project's end!