73954 ((ABICSEA)) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from CORSICANA, TX
- Parts Used:
- 4984JJ3003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
old bushing worn and broken
removed the upper freezer door to access screws to remove lower door.
laid bottom door on its side, removed bad bushing, put new bushing in, put bottom door back on refridge, put upper door back on fridge. Door worked easy as when new. good closure of door and story..Happy customer, and wife even happier.....thank you....
laid bottom door on its side, removed bad bushing, put new bushing in, put bottom door back on refridge, put upper door back on fridge. Door worked easy as when new. good closure of door and story..Happy customer, and wife even happier.....thank you....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from PHILADELPHIA, PA
- Parts Used:
- 4984JJ3003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
bottom door dropped slightly and bottom hinge area rubbing on steel door support
removed 3 fasteners for top door and placed freezer door aside, then removed 3 more fasteners on bottom refrigerator door and place that aside. replaced bushing on lower door bracket and reversed the above procedure to reinstall doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from TROY, MI
- Parts Used:
- 4930JJ2021A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
two screws and done
part fit into slot and screwed them down
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Renita from FORT MADISON, IA
- Parts Used:
- 4930JJ2021A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken clip that keeps the lower holder cover from falling off bottom of refregerator
Used a screwdriver to take off broken clip and then used same screwdriver to replace with new clip. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norris from Telford, PA
- Parts Used:
- 5989JA0002N
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
icemaker stopped working
This is bottom drawer type frige. Icemaker is inside (not in the door) and hard to reach. I first tested the solenoids by disconnecting them and using a test cord, energized them independent of the frige wiring. They worked ok. Note: this frige has (2) solenoids going to the icemaker. And it has (3) solenoids serving the water dispenser. The icemaker solenoids are wired in parallel. I removed the icemaker by removing (1) screw from the bottom and loosening (2) on the top. Then removed icemaker as a complete unit disconnecting the wire connector at the same time. On the bench I tested the icemaker to verify it was defective. The wire harness has a 10 amp fuse in the black wire (hot wire). `The fuse was blown. This was sufficient to indicate the icemaker is shot. I did however, do some other tests. Cold resistance of the mold heater was 72 ohms. The timer motor was 4000 ohms. These measurements should be ok. I then activated the icemaker with a test cord, bypassing the blown fuse. The unit cycled one complete rotation then stopped. The mold heater worked. I tested the amp draw on the mold heater and it was only .1 amps. I should be a about .8 amps. I then cycled it again and then the timer motor began to sizzle and smell. Then it smoked and stopped mid-rotation. I then purchased a new icemaker. I believe the mold heater was going bad over time as this unit made ice but very slowly. This put extra strain on the motor as the mold was not releasing quickly. This damaged the motor causing it to fail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from DICKSON CITY, PA
- Parts Used:
- 4930JJ2021A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace lower grill bracket
Pull off the grill cover and remove the 2 screws from the old part and simply screw in the new part. Don’t lose the screws there are no new ones with the new part. Replace cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from NEWPORT NEWS, VA
- Parts Used:
- AJU55759303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
The ice maker fill valve died.
Went on line to see how difficult it would be to replace the valve. Through Google there was a video which showed in exact detail how to remove and replace the valve. Then went on line to find the replacement part which was readily available. The only problem was that the connection on the valve where the fill water enters the valve was larger than the old valve. To fix that I went to a local Ace hardware store and found a nut that would fit the valve connection. Also don't forget to use a compression ring to keep the fill line secured when replaced.
Over all it was very simple and was in my "pay grade"
Over all it was very simple and was in my "pay grade"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SAVOY, IL
- Parts Used:
- 6600JB2004F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator not cooling. Fan and lights not working also.
In plug refrigerator. Pry old switch out with flat blade screwdriver. Disconnect wiring from old switch and plug into new switch. Push back into refrigerator. Plug unit back in. Lights and fan should now work. Check for cold air coming out in freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from FLORISSANT, MO
- Parts Used:
- AJU55759303
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Ice maker not working but making a sound when turned on (buzzing). Water valve not functioning when tested with a multitester (multimeter).
I removed the old water valve, disconnected the water tube going in and tube going out to the back of the refrigerator. New water valve bracket different than the previous one which resulted in my having to modify it to fit. Not an easy task as it was preformed metal. Once hooked up, water turned on, and ice maker turned on, the sound I'm getting now is clunking and not making ice. My debate is whether or not to purchase a new ice maker or revert to the tried and true method with ice trays which work every time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ilene from Lincoln, NE
- Parts Used:
- 3391JJ2004G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drawer was broken and replaced it
Just put the drawer in and it was ready to go. Like those kind of repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Lawrenceville, GA
- Parts Used:
- AJU55759303
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
My ice-maker was making almost no cubes
Pulled the fridge out of its space. Removed a metal shield which covered the bottom 12" of the fridge with a Philips head screw driver. The water valve is on your right. turned off the water to the supply line. Removed the supply line using an adjustable wrench. Removed the water line gong from the pump into the fridge. It is held on with a "C" clip which can be pulled off with needle-nose pliers. Removed the old pump, held with one Philips head screw. Then installed the new pump, reconnected the lines, replaced the metal shield and turned the water back on. Vacuumed the fridge and its space before cleaning up. The ice-maker now works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from Huntsville, TX
- Parts Used:
- AJU55759303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water was leaking into the ice maker and into the ice bucket
I removed the cover from the rear of the unit, with a screwdriver. Then with a adjustable wrench unscrewed the top nut of the water valve.I then removed the screw holding the valve to the wall of the fridge. Turned the valve upside down and removed the line going up to the ice maker. No tools needed here as it is a quick connect fitting.Use reverse order to install valve.I am 65 years old and if I can do this anyone can. Good luck from TX.
Was this instruction helpful to you?
Thank you for voting!