Models > 74305

74305 LG Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Handle Screw – Part Number: MJB63190001
$14.65
This part includes a single mounting bolt needed to secure the door handle to your refrigerator. This part is commonly replaced because the handle has started to loosen. Try tightening the screw first...
In Stock
Order now and your part arrives by Mar 19
Door Bin – Part Number: AAP73252202
$72.37
Refrigerator door bin AAP73252202 is an original equipment manufacturer (OEM) part that fits some Kenmore Elite bottom-freezer refrigerators in the following series 7957204, 7957205, 7957209, 7957218,...
In Stock
Order now and your part arrives by Mar 19
Door Shelf Bin Assembly – Part Number: AAP73252302
$64.21
Need more space in your fridge door? This clear, gallon-sized bin is a great way to organize drinks, sauces, and jars. It fits on the right-side door of certain refrigerators and installs easily—no to...
In Stock
Order now and your part arrives by Mar 19
Door Gasket – Part Number: MDS38201426
$78.95
Freezer door gasket is on the inner door panel and creates a seal around the door to prevent warm air from entering the freezer compartment.
In Stock
Order now and your part arrives by Mar 19
Door Gasket Assembly – Part Number: ADX72930461
$98.95
Keep your LG refrigerator running efficiently with this replacement door gasket, also known as a door seal. It helps block warm air from entering the fridge, preserving the cool temperature inside. If...
In Stock
Order now and your part arrives by Mar 19
Micro Switch – Part Number: 6600JB3001C
$30.85
In Stock
Order now and your part arrives by Mar 19
GASKET ASSEMBLY,DOOR – Part Number: ADX72930460
$98.95
Keep your fridge cool and efficient with this replacement door gasket. Made from flexible rubber, it lines the edge of the refrigerator door to seal in cold air and keep warm air out. If your current ...
In Stock
Order now and your part arrives by Mar 19
Refrigerator Ice Maker – Part Number: AEQ73130004
$185.95
The ice maker includes the ice mold and the control device. The ice maker receives water from the water inlet valve and then holds the water in the ice mold until the water freezes solid.
In Stock
Order now and your part arrives by Mar 19
WATER INLET VALVE – Part Number: AJU72992603
$131.95
In Stock
Order now and your part arrives by Mar 19
Rail Connector – Part Number: 4932JA1010B
$23.05
In Stock
Order now and your part arrives by Mar 19
Clip – Part Number: 4004JA3002A
$30.85
Special Order
ICE BUCKET – Part Number: AKC73369914
$185.95
This replacement ice bucket assembly includes the bin and auger used to store and dispense ice in compatible refrigerators. It’s ideal for replacing a broken or worn-out unit and helps restore proper ...
On Order
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 74305

Viewing 9 of 9
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door Sweating
Fixed by these parts
Fixing Fixing
How to fix it
Ice maker not making ice
Fixed by these parts
Fixing Fixing
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing
How to fix it
Door won’t open or close
Fixed by these parts
Fixing Fixing
How to fix it
Not dispensing water
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing
How to fix it
Ice maker dispenses too much ice
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeff from HUMBLE, TX
Parts Used:
AEQ73130004
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice Maker Quit Making Ice
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo re you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Read less
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Vispi from SUGAR LAND, TX
Parts Used:
ADX72930461, ADX72930460
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The door gaskets had become hard and curled up - would not seal properly
Watch YouTube videos on this topic if you are uncertain before tackling the job. The right door was easy to replace. Just pull the gasket with your fingers and it will come off easily. Place new gasket over door and use fingers to press it inside the groove few inches at a time. Pay attention to gasket orientation.

The left door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.

Could not believe how easy it was!
Read less
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Megan from Elk Grove, CA
Parts Used:
ADX72930461, ADX72930460
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replaced Old Molded Gasket with new one
For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.

For the left side, needed a Phillip’s screwdriver to remove the flap first. H elps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.

Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.
Read less
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More