Models
>
GM-L267BNRY
GM-L267BNRY LG Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$15.26
This part is the replacement ice tray for your refrigerator. The tray is made of white plastic and is approximately 9 inches in length, and 3 inches in width. It has the capacity for 8 ice cubes. The ...
Special Order
$136.67
This water inlet valve has three solenoid valves and push in fittings. When energized this part releases water from the supply line into the ice mold.
In Stock
Order now and your part arrives by Aug 15
$86.45
This cooling fan motor helps regulate your refrigerator’s temperature by moving air over the condenser coils to prevent overheating. A faulty motor can lead to poor cooling or unusual noises. Installa...
In Stock
Order now and your part arrives by Aug 15
In Stock
Order now and your part arrives by Aug 15
In Stock
Order now and your part arrives by Aug 15
$360.30
This part holds the ice once it's released from the icemaker. When activated, the auger rotates and pushes ice out of the bin through the chute to the user.
This assembly includes the auger and blades.
On Order
Special Order
$94.45
This evaporator fan motor is a replacement drive component designed to circulate air across cooling surfaces. It supports even temperature distribution and is commonly replaced when airflow decreases ...
In Stock
Order now and your part arrives by Aug 15
In Stock
Order now and your part arrives by Aug 15
Common Problems and Symptoms for GM-L267BNRY
Viewing 6 of 6Leaking
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not dispensing water
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from ATLANTA, GA
- Parts Used:
- 3390JA1150A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice tray had warped and dumped water, which then froze down through the ice bucket and below.
To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting.
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.
/Users/grf/Desktop/fridge ice tray.pdf
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.
/Users/grf/Desktop/fridge ice tray.pdf
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from DEMOPOLIS, AL
- Parts Used:
- 4987JJ1010M
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Gasket on refrigerator door
The replacement gasket does not have as strong a magnet as the original one. I removed the old one carefully so as not to cause more damage in case I have to put it back. Using Tongue suppressor I pushed new gasket into place and put a thin coating of protelem jelly on the gasket. I just have to make sure the door is closed each time to
... Read more
be sure of good seal.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from NORTHRIDGE, CA
- Parts Used:
- 5221JA2006D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
whater valve whith a defected selenoid and water leaks.
First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.
Read less
Was this instruction helpful to you?
Thank you for voting!