Models
>
KBSD612ESS01
KBSD612ESS01 KitchenAid Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KBSD612ESS01
Viewing 14 of 14
Keep searches simple, eg. "belt" or "pump".
It is recommended to replace your refrigerator water filter every 6 months or 200 gallons of water. This will ensure consistently good-tasting water that is free of pollutants. This NSF-certified filt...
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
$37.20
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
In Stock
Order within the next 3 hrs and your part ships today!
$14.58
This part is a replacement refrigerator drive shaft seal for your refrigerator. The drive shaft seal protects the auger motor from water and condensation that may leak down the drive shaft from the ic...
In Stock
Order within the next 3 hrs and your part ships today!
$39.20
This part is a replacement flipper or emitter cover for your refrigerator. It is made of white plastic and is approximately 3 inches by 2 inches. The flipper shields the emitter control board and hous...
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
$7.95
This is the replacement ice maker cover bracket for your refrigerator. It is made of white plastic and is approximately 5 inches wide and 2 inches long. The ice maker cover bracket holds and supports ...
In Stock
Order within the next 3 hrs and your part ships today!
Sold Individually. - * Part may differ in appearance, but functions same as original.
In Stock
Order within the next 3 hrs and your part ships today!
$5.42
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KBSD612ESS01
Viewing 10 of 10Light not working
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not dispensing water
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Ice maker dispenses too much ice
Fixed by these parts
How to fix it
Ice maker dispenses too little ice
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kate from Jacksonville, FL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
there were directions
We didn't know where the product went and it was very difficult to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy from Perkiomenville, PA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
six months the light turns red. time to replace filter
First I shut the water off to the refrigerator.then i pushed the big button in the middle of the grille below the refrigerator door. pulled out the old filter, took the front cap off the old filter put it on the new filter. took the two red caps off the new filter. pushed the filter in till it locked in place. all done! Turned the back on
... Read more
.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vince from El Cajon, CA
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker would not stop making ice.
First, I tested the ice maker "switch" that actually just covers the beam that regulates the ice maker. In the "off" position, it still made ice. Then, I removed the three screws on the cover over the transmitter and disconnected the circuit board at the wire connector. It stopped. After ordering and receiving the new transmitter and rece
... Read more
iver boards, I replaced both boards. They are located on either side of the freezer compartment under panels held in place by three screws. Probably saved 150 to 200 bucks.
Read less
Was this instruction helpful to you?
Thank you for voting!