KRFC300ESS01 KitchenAid Refrigerator - Instructions

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.

I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!

Removed door and crisper pans.
Removed nuts on left end cap - think there were 3.
Removed nuts on right end cap and one or two on back air regulator attached to right end cap.
Replaced left end cap with new one using reserved nuts.
Carefully removed back air regulator from right end cap.
Attached back air regulator to new right end cap.
Replaced right end cap and back air regulator and attached with nuts.
Carefully inserted pantry door into pin on one side and slightly bent both right and left pins to insert door fully into end caps.
Replaced crisper pans.
That's it.

The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!

I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

Crisper drawers:
1. Removed crisper drawers from refrigerator.
2. Removed drawer front decoration panels.
3. Unpacked, inspected and rinsed out new drawers.
4. Attached drawer front decoration panels.
5. Transfered vegetables and fruit from old drawers to new drawers.
6. Installed new drawers in refrigerator.
7. Closed refrigerator door.
8. Total time about 15 minutes, no tools required.

Ice & Water filter
1. Opened filter compartment cover
2. Removed old filter, drained into sink and placed in the trash.
3. Installed new filter
4. Bled the water line with ice water tap button (be aware when the air in the line exits the spigot, it create a lot of spray and you may need to cleanup the water that splash out of the bottom of the container used to capture the water during the bleeding process.)
5. Close the filter cover and refrigerator door.
6. Total time about 10 minutes and no tools required.

Removed two screws that held cover plate. remove cover plate. Remove water hose, and clamp, by compressing clamp with pliers. Remove fill tube by pulling HARD, from back.

Replace fill tube, check to be sure that it entered ice maker properly. Replace hose and clamp.
Replace cover and screws.

unscrewed to removed old and screwed in new

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.