KRFC300EBS09 KitchenAid Refrigerator - Instructions

Removed door and crisper pans.
Removed nuts on left end cap - think there were 3.
Removed nuts on right end cap and one or two on back air regulator attached to right end cap.
Replaced left end cap with new one using reserved nuts.
Carefully removed back air regulator from right end cap.
Attached back air regulator to new right end cap.
Replaced right end cap and back air regulator and attached with nuts.
Carefully inserted pantry door into pin on one side and slightly bent both right and left pins to insert door fully into end caps.
Replaced crisper pans.
That's it.

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

The mullin requires only one screw removal, then LIFT the entire mullin upwards. Pop the wire harness loose, and replace with new mullin. Simple job,

We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in the pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.

Removed the grill and control cover in the top middle of the main compartment, removed the control, unplugged it and put in the new one. The thing that took the longest was figuring out that this was the part that needed replacing. The fridge is less than two years old and about 6 months ago the control started making these odd noises. Now it's quiet. Ah peace!

The lid that covers the front of the lower meat / produce drawer hinges upward on two small ( easily broken) plasic pins, one on each side of the drawer. One pin is moulded into each "END CAP" that also supports the drawer glides and glass shelf above. The entire end cap must be replaced to repair the hinge. The left side is easy (it's the only one I had to replace); the right side might be more difficult because the right end cap includes a temperature control.
1) Remove the two produce drawers above the lower drawer.
2) Lift off the front glass shelf support, the glass shelf, and the rear glass shelf support from below the two produce drawers.
3) Slide the lower drawer half way out. Remove the drawer lid by disengaging it from the remaining undamaged hinge pin on the OK end cap. Careful not to break the good one.
4) Slide the lower drawer all the way out, then lift up and towards you to remove it from its glides.
5) Using a 1/4" nutdriver or socket, remove the three recessed screws. Leave the drawer glide alone for now.
6) Pull the front of the end cap up and towards you about 3/4" to disengage it from a small retainig button at the top front. Pull the end cap toward you to disengage the two rear retaining fingers.
7) Using a small Phillips screwdriver, remove the drawer glide from the broken end cap and attach it to the replacement end cap. Note which end is the front before removing it.
8) Reassemble in reverse order. Again, be careful with the hinge pins.

First, I removed the old door gasket by pulling it out of the channel it was mounted in, noting the orientation of the gasket. Then, it was a simple matter of lining the new gasket up with the channel and pressing it into the groove. Very easy repair, and the door seals great!

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.

First I looked at new replacement part, saw what held the part to the frig. Then removed the crisper drawers and vegie drawers and related support pieces. Used socket wrench to take out three screws and started so remove endcap. Realized endcap was attached to a piece that controls air flow to drawer, located supporting screw, removed and entire assembly came right out. I fumbled my way through the linking mechanism being very careful not to force and break anything. Once I figured out how all this worked, it went back together in a few minutes. Replaced the four screws that held the 2 pieces (endcap and airflow) to frig, replace drawer slid, replaced all draws. Done 30 minutes, start to finish. I found Customer Service VERY helpful while ordering piece, couldn't believe it was under $10 and fit exactly! Thanks PartSelect.com!

i did not need the can holder in door, we do not buy can drinks. i would rather have the full shelf space, so i replaaced the can holder with a full shelf

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

First, I removed the drawers at the bottom of the fridge and then I removed the three hex head (7/32) screws that hold the end cap on. Then I disengaged the slider which connects to the temperature control for the pantry drawer. Then, unscrewed the drawer slides with a Phillips from the old end cap. Also the slide push rod has to be disengaged from the clips on the back of the endcap.

Then, I reinserted the push rod to the new end cap and reattached the drawer sliders and the slider itself. At this point I realized I SHOULD have unscrewed the temperature slider at the back where it covers the cold air outlet. The screw had slipped out. I replaced it with a slightly larger wood screw. Reinstall the drawers, all done.

Since the crisper didn't come with a front, the old front needed to be removed from the broken cripser and attached to the new one. The easiest way to take off the front is to remove it from the bottom of the crisper. Once the pressure is released it comes off easy. Snap the front on the new crisper by starting with the top and snapping the bottom.