25370443210 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ed from PETALUMA, CA
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old door gasket was worn and edge was cut
Pulled the old gasket out if groove on the door, cleaned inside the groove, squirted some windex in the groove to ease the new gasket in the groove, then proceeded to work the gasket into the groove. Made sure gasket was all the way in the groove around the perimeter of the door. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from CHEVY CHASE, MD
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original refrig door gasket was fraying
It's too easy to describe.
What's more important is that someone read this and see that you can save hundreds of dollars doing this repair yourself. I'm sure many handy people think that about everything they repair, but this repair is insanely easy and the $ savings ridiculous.
When I called the place I purchased the refrigerator from, they were more than happy to sell me the part with a 35% markup (your price was reasonable) and (when i asked) they told me that sending someone to my home to make the repair would cost about $400 ($200 per door) including the "home instal" fee.
I removed the old gaskets and put on the new ones (on both doors) in under 10 minutes. I confess that I did the job under the auspices of my very handy son but he'll agree with everything I just wrote. To the unhandy: go forth and replace your own gaskets.
What's more important is that someone read this and see that you can save hundreds of dollars doing this repair yourself. I'm sure many handy people think that about everything they repair, but this repair is insanely easy and the $ savings ridiculous.
When I called the place I purchased the refrigerator from, they were more than happy to sell me the part with a 35% markup (your price was reasonable) and (when i asked) they told me that sending someone to my home to make the repair would cost about $400 ($200 per door) including the "home instal" fee.
I removed the old gaskets and put on the new ones (on both doors) in under 10 minutes. I confess that I did the job under the auspices of my very handy son but he'll agree with everything I just wrote. To the unhandy: go forth and replace your own gaskets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- melvin from BASKING RIDGE, NJ
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
you r label (this end in arrow is wrong
placed filter in sideways
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from CHICAGO, IL
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn gasket
Replace gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Mount Juliet, TN
- Parts Used:
- 5303918899
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer Cold, but Refrigerator not Cold
We replaced the damper, but it didn't fix the problem. We then purchased and replaced the thermistor. (We had previously replaced the defrost thermostat). The refrigerator side is now cooling better, but not enough. The damper doesn't seem to be opening. So we have now unplugged the damper and left the opening between the refrigerator propped open and the refrigerator side is now cool enough. (We had previously tried keeping the damper open before we replaced the thermistor and the refrigerator didn't cool off. So the thermistor did fix something, but the damper doesn't seem to have been the problem).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from GREENVILLE, NC
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Gaskets needed to be replaced
The instructions that were provided were perfect. Easy step by step. Entire installation took only 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from WETUMPKA, AL
- Parts Used:
- 242094802, 5303918568
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Frost build up behind "in refrigerator" ice maker. Ice maker mold temperature above 20 degrees inhibiting ice making
Used the following video link to replace thermostat:
https://www.youtube.com/watch?v=4JnBZuXpehw
Since problem was frost build up on coils behind the ice maker I figured the problem had to be the thermostat or the heater coil. All diagnostic tests on ice maker worked fine. Ordered both...50-50 chance. Turned out to be the thermostat, but replace both. Working good now.
https://www.youtube.com/watch?v=4JnBZuXpehw
Since problem was frost build up on coils behind the ice maker I figured the problem had to be the thermostat or the heater coil. All diagnostic tests on ice maker worked fine. Ordered both...50-50 chance. Turned out to be the thermostat, but replace both. Working good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GRAY, ME
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was torn and leaking cold air causing condensation and water dripping when door was opened.
I pulled the old one out and pushed the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from POTTSTOWN, PA
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
NO PROBLEM JUST DECIDED IT WAS TIME TO CHANGE FILTER
VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul S Van from BRUNSWICK, ME
- Parts Used:
- 242194301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Trim on door water/ice dispenser broke off
Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.
About two minutes.
About two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from GRIFTON, NC
- Parts Used:
- 242220204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Brookfield, CT
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator wasn't staying cool enough
Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oley, PA
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..
Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.
Was this instruction helpful to you?
Thank you for voting!