5649936080 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mickey from Novato, CA
- Parts Used:
- WP304204
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the 4 latches that holds the spray arm to the top rack broke and fell off.
It just snaps back in but it was a very tight fit and took two people to force it in. Plus I had no instructions and hadn't seen it before it broke so it took a little time to figure out where it was supposed to go. The arm doesn't connected to anything except the rack. I guess water just shoots up into it from below.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from Colorado Springs, CO
- Parts Used:
- WP304204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray Arm broken off
It was so easy , I first put one side of the clamp on the little rack area in the center of the upper rack then pushed the other side on. It took less than five minutes. No tools needed. Julia
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from REIDSVILLE, NC
- Parts Used:
- W11086533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed a tub sound shield
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hank from Arlington, TX
- Parts Used:
- WP304204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm mounting clips broke
Simply snapped new spray arm in place. Took longer to get the soray arm out of the shipping package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from JACKSONVILLE, FL
- Parts Used:
- W11169039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper dish rack broken tines
Swapped out the old upper dish rack with a new one. A video made the change simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from VALLEJO, CA
- Parts Used:
- WP304204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing Spray Arm Broken
Snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audrey M. from Attleboro, MA
- Parts Used:
- WP304204
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper spray arm broke off.
Had to clip the part onto the upper rack. It was a little tight at first, then all of a sudden it just snapped in. Voila, as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Bellevue, OH
- Parts Used:
- WP304204
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Remove/Replace Upper Spray Arm
Tried using my hands to bend back the locking plastic connectors enough to get them onto the metal upper storage rack;was afraid of breaking the connectors so I used my utility tool needle nose pliers to give me leverage. This time I was successful. Believe me,it was frustrating for what seemed a long time. No,for me it was not easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!