79572053117 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from EASTON, PA
- Parts Used:
- MJU62070602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water feed line running from water valve to filter housing was leaking
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from MUKWONAGO, WI
- Parts Used:
- EAU59551204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice chute would not open.
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from SPARKS, NV
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Changing out the Ice Maker tube
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders Lay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders Lay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LA PLACE, LA
- Parts Used:
- AEQ73110203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker wore out.
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from MARS HILL, NC
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge waterline for ice maker / door water
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from SPRING HILL, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice crystals appearing on the face of the freezer draws
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Konnie from SALEM, OR
- Parts Used:
- ADX72930461, ADX72930460
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Moldy and torn gaskets
Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from VALE, OR
- Parts Used:
- 6600JB3007K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The lights wouldn't always come on.
I actually watched a YouTube video for LG refrigerators. The hardest part was taking the wire harness out. Mine was really stuck in there. But got it, put the new switch in and viola it worked. Yay!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from KENT, WA
- Parts Used:
- AAP73252202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The shelf on our refrigerator was cracked so I ordered a replacement.
Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from SACRAMENTO, CA
- Parts Used:
- AAP73252202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Basket
Un-wrapped the basket......Installed with NO tools......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from CLEBURNE, TX
- Parts Used:
- MJU62070602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced hose and it was exactly what I needed.
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from RICHMOND, VA
- Parts Used:
- AAP73252302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ordering the right parts
I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WES from SOUTHLAKE, TX
- Parts Used:
- ACQ85428602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Cracked crisper tray unit cover assembly
Remove glass cover, take out both humidity and air tight crisper drawers, then remove the cover assembly.
Reassemble with new cover
Reassemble with new cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FONDA from KATY, TX
- Parts Used:
- AAP73252202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door basket broke
Opened the box. Removed wrapping. Washed the new part. Unloaded old basket. Removed old basket. Set in new basket. Loaded new basket. Closed the door. Even an 80 year old can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DICKINSON, TX
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Freezer door gasket needed replacing.
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Was this instruction helpful to you?
Thank you for voting!