2539308012 Kenmore Refrigerator - Instructions

After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.

I wrote down the Brand and model# of my refrigerator. googled it and PartSelect came up. I mean it literally took me 5 minutes to select the part, and order it! I ordered it on a Saturday and the part arrived on Tuesday! And it was a perfect fit! I will always return to PartSelect for any replacement parts for my appliances! Thank you!

Door would not stay closed so I decided to replace the gasket... The new gasket install was easy and quick. I removed the liner and took off the old gasket, placed the new gasket on the liner and reinstalled the liner. However that did not fix the original issue of the door not closing. I followed all the instructions listed on the web site but none corrected the problem. The door on this model has no adjustment. So I adjusted the leveling wheels to tilt off center towards the back. That helped but still did not resolve the problem... I then closed the door slowly to see if it was being interfered with, As it turns out it was being hit by the bottom of the inside of the refrigerator. Since I could not adjust the door, I used the front leveling wheels to compensate for the lack of door adjustment. I slowly kept adjusting the w heels to see what effect it had. I finally adjusted them to the point were the door now closes and seals on its own. I’m guessing that over time the liner became malformed and caused the door to hit the inside of the refrigerator. After it started working I checked the level side to side and front to back. Side to side is good and there is a slight tilt to the rear.

Removed the old drawer. Put the front on the drawer which ws a little tricky but with the help of a screw driver to gently pry the drawer the front went on easy.
Put the drawer in the refrigerator.

Just like that.

The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the pan above the threads of the bolt so as not to damage the threads). I still had to cut half the bolt away with a hack saw by replacing the nut and cutting a third of the bolt away (above the nut), so the new pan would fit. Putting the new pan on was a breeze after that. It may be easier to just cut the bolt off altogether on top of the compressor and use the wire clips per the instructions supplied with the kit to install the new one.

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement switch.

Removed old gasket. tried to mount new gasket with a few screws, but weight of new gasket created a sag, so I removed door and laid on a table. Installed new gasket, as it layed flat and square on the table. Installation became a simple job.

Twisted replacement bulb into place easily. Let there be light!

ordered the glass and installed it

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

First I let the gasket lay flat on a hard surface in the sun for several hours. Then I removed old gasket and placed new gasket in place and utilized some glue substance to hold it in place.
Easy enough--hope refrigerator will be more energy efficient

Vacuumed out the glass and placed the new shelf in the slots. Arrived quickly and fit perfectly!

Simply removed (many) screws from the door shelving panel. Removed old gasket, installed new one and screwed it back on. A rather simple repair that will allow me continued use of my older fridge.

i simply snaped one end cap in put retainer in on sie put other end cap on retainer then snaped end cap in place --job done parts where perfect thanks

Removed all the screws. Replaced the gasket put all the screws back. This would work great if the door wasn't out of alignment.

Now I have a new refridgerator coming on Monday.