PFSS9PKYASS General Electric Refrigerator - Instructions

Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.

The installation video notes that the door mullion spring has a bent end, and that the bent end of the spring is to be inserted into the LOWER hinge. However, on my refrigerator door, the bent end of the door mullion spring must be inserted into the UPPER hinge in order for the door to function properly. (Also noted that in your video the installer manually closed the door mullion rather than just closing the refrigerator door, another indication that the installation of the spring was incorrect.) After watching the video several times to confirm I was installing the door mullion spring according to the video instructions, I tried inserting the bent end of the door mullion spring into the upper hinge, which proved to be the correct installation of the door mull spring. What should have been a 5 minute repair turned into an ½ hour repair.

unscrewed old filter by hand, installed new filter.

Until I figured out that the Metal cover on the divider door had to be removed (pried out) giving access to the hidden hinges. After that the hinges could be removed and replaced.Great with giving phone thou.

I just replaced the broken spring and the little plastic cylinder that goes over the end of one part of the spring. I placed the plastic part on first and slid it in place, then had to bed the other end of the spring a little bit to place it in the hole. But once it went in, the door worked perfectly. And I'm a 70 yr old woman. So if I can do it, anyone can.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

Just opened the french door took the new plactic sleeve placed it on the upper end of the spring and then inserted into the upper hole first then with a little pressure turned the bottom end of the spring and placed it into the lower hole.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unscrewed 1 screw, removed panel, disconnected old icemaker and removed it, Added new icemaker, reconnected, replaced panel, replaced screw, & reset new icemaker. Started making ice almost immediately. Threw out entire first load of ice. Working great since! I wasn’t sure if it was the icemaker or the water valve to it so had a guy come out ($50) who confirmed it was the icemaker. He wanted $550 to replace it (part/labor). We bought the part here at Part Select for $185 (part/tax/delivery) and saved $265 on a job that took less than 15 minutes.

Went to You Tube and saw video on how to replace broken mullion spring. Ordered part online (more than one in case one broke -very cheap <$3.00 per part). Watched video twice and was able to follow instructions and insert spring correctly. Not difficult if you pay attention to details on how the spring must fit and which end goes where. The door works perfectly!

There is a pretty good video about this on youtube, but complications arose nonetheless. The replacement spring supplied by Partselect is a bit different from the original in two ways. First, it is made of heavier-gauge wire; this is a good thing for durability, but it makes installation tougher. Second, the ends of the spring, which are bent at right angles to the spring axis in order to fit into the plastic sleeves that hold the spring ends, are far too long. Once I figured this out, i snipped the ends down by a quarter inch or so, and they fit into the sleeves just fine after a certain amount of persuasion from needle-nose pliers. All things considered, it was a bit harder than it should have been, but the door works now, so all is well.

Leaking icemaker assembly was causing all of the ice cubes in the ice tray to freeze together. Remove ice tray, remove one Philips screw, pull the cover off, unplug the wires, remove the icemaker assembly by pushing tab and pulling the assembly at the same time. Replaced the water filter as well.

By hand. It was a very easy fix!

Went on the Internet to find the installation instructions.