Models > GSS20GEWJCC

GSS20GEWJCC General Electric Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for GSS20GEWJCC

Viewing 8 of 8
FREEZER DOOR Diagram and Parts List for General Electric Refrigerator
FREEZER DOOR
FREEZER SECTION Diagram and Parts List for General Electric Refrigerator
FREEZER SECTION
FREEZER SHELVES Diagram and Parts List for General Electric Refrigerator
FREEZER SHELVES
FRESH FOOD DOOR Diagram and Parts List for General Electric Refrigerator
FRESH FOOD DOOR
FRESH FOOD SECTION Diagram and Parts List for General Electric Refrigerator
FRESH FOOD SECTION
FRESH FOOD SHELVES Diagram and Parts List for General Electric Refrigerator
FRESH FOOD SHELVES
ICE MAKER & DISPENSER Diagram and Parts List for General Electric Refrigerator
ICE MAKER & DISPENSER
SEALED SYSTEM & MOTHER BOARD Diagram and Parts List for General Electric Refrigerator
SEALED SYSTEM & MOTHER BOARD

Manuals & Guides for GSS20GEWJCC

Click to download
Manual
Owner's Manuals
(10.98MB)
Manual
Owner's Manuals
(13.23MB)
Manual
Owner's Manuals
(13.78MB)
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor – Part Number: WR55X10025
$27.00
The temperature sensor, also referred to as a thermistor, is used to monitor the refrigerator and freezer internal temperatures. The sensor is a small capsule like device that is protected by a white ...
In Stock
Defrost Thermostat – Part Number: WR50X10068
$29.26
If your freezer has a buildup of frost, or is not maintaining the proper temperature, there may be an issue with the defrost thermostat. This device stops the evaporator coil from overheating while th...
In Stock
Drawer Slide Rail - Right Side – Part Number: WR72X240
$42.55
This genuine OEM part is the right side of the slide rail for the crisper drawer in your refrigerator. This rail is attached to your fridge wall with two screws and will require a Philips screwdriver ...
In Stock
Drawer Slide Rail - Left Side – Part Number: WR72X239
$29.73
This drawer slide rail is a genuine OEM replacement part for the crisper drawer shelf in your refrigerator. This rail is for the left-hand side of the shelf assembly. If you need to replace both sides...
In Stock
Defrost Heater Harness Kit – Part Number: WR51X10101
$61.67
This dual heater kit replaces the single heater. It's redesigned to use two heating elements for a better defrost cycle.
In Stock
Ice Maker – Part Number: WR30X10093
$216.23
The ice maker assembly makes ice by filling the tray with water from the inlet valve, freezing it until solid cubes are formed, and then ejecting them into the ice bucket. This process will repeat unt...
In Stock
Dispenser Door Assembly or Flapper – Part Number: WR17X11653
$15.58
This is a genuine OEM replacement door flap for the ice maker in your refrigerator. This part goes by many different names, including door recess assembly, ice door assembly, dispenser door, ice chute...
In Stock
Dispenser Door Solenoid Assembly – Part Number: WR62X10055
$64.74
The dispenser door solenoid is the part that controls the flapper door on your ice maker, allowing it to open and close when dispensing ice. If your ice maker is not dispensing ice or water, the door ...
In Stock
Recess Door Spring – Part Number: WR02X10585
$9.17
This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find th...
In Stock
DISPENSER LIGHT – Part Number: WR01X37886
$17.85
This OEM dispenser lightbulb is sold individually. This light bulb is responsible for lighting up the dispenser area of your fridge. It is 12 volts, 6 watts, and has a screw-in base. For this simple t...
In Stock
Union Connector - 5/16 Inch to 5/16 Inch – Part Number: WR02X11330
$9.03
Quick connector for plastic water line - 5/16" to 5/16"
In Stock
Evaporator/Condensor Fan Grommet – Part Number: WR02X10098
$11.59
This grommet is found on both the front and back of the fan motor assembly for the condenser and the evaporator in your fridge. It is used to provide a buffer between the fan motor and the mounting br...
In Stock
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for GSS20GEWJCC

Viewing 27 of 27
Fridge too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Ice maker not making ice
Fixed by these parts
Fixing Fixing
How to fix it
Freezer not defrosting
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not dispensing water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge too cold
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Light not working
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t open or close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door Sweating
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer too cold
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Ice maker dispenses too little ice
Fixed by these parts
Fixing Fixing
How to fix it
Too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge runs too long
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing
How to fix it
Clicking sound
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Ice maker dispenses too much ice
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Doesn’t stop running
Fixed by these parts
Fixing Fixing
How to fix it
Won’t start
Fixed by these parts
Fixing Fixing
How to fix it
Engine revs but auger will not turn
Fixed by these parts
How to fix it
Too cold
Fixed by these parts
Fixing
How to fix it
Engine runs but cutters do not turn
Fixed by these parts
How to fix it
Replacing the Temperature Sensor

Replacing the Temperature Sensor

Replacing the Ice Maker

Replacing the Ice Maker

Replacing the Drawer Slide Rail - Left Side

Replacing the Drawer Slide Rail - Left Side

Replacing the Drawer Slide Rail - Right Side

Replacing the Drawer Slide Rail - Right Side

Replacing the Dispenser Door Solenoid Assembly

Replacing the Dispenser Door Solenoid Assembly

Replacing the Condenser Fan Motor

Replacing the Condenser Fan Motor

Replacing the Dispenser Door Assembly or Flapper

Replacing the Dispenser Door Assembly or Flapper

Replacing the Defrost Thermostat

Replacing the Defrost Thermostat

View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Tim from Newport News, VA
Parts Used:
WR29X43990
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Plastic Auger blades broke in ice tray
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with small flathead screwdriver. Slide white top cover up and you will now see the metal blades and assembly. Auger is held in place with a metal c-clip and washer on the end. Use flat head screwdriver to pry off c-clip. Then you will see a nylon round slotted nut. The threads are reverse, use pliers and loosen nut. It is not that tight but pliers are needed. Then it all is loose and ready for removal. I slid all the blades off at one time and kept them stacked together. Slide out auger and clear flat shield cover. Install new auger, clear shield, and metal blade stack. When you put it all back together take a look at the long metal J-hook on the bottom make sure it is in the slot before you make everything tight. Failing to do this will prevent cubed ice from dispensing.
It is not that hard to do the repair it just takes some patience and paying attention to details.
Read less
583 of 621 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Greg from Aledo, TX
Parts Used:
WR51X10101, WR50X10068
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Ice box and freezer would not get cold,the back wall of the freezer was covered with ice
1. I had to defrost the ice off of the back wall of the freezer with a blowdryer.
2. Removed the four 1/4'' screws and removed the back panel.
3. Defrosted all of the ice off the coils and heater.
4. I replaced the defrost thermostat and heater by following the directions that came with them. The directions are very clear a nd easy to follow. I had a single element heater, and the replacement was a double element, the directions even explained how to rearrange the wires to make it work. The whole job only really consisted of cutting two wires that are color coded on the thermostat and resplicing the new ones in. I used scotch locks and electrical tape for the splices. The element had connectors on it so I just removed two screws, unplugged two wires and plugged them on the new one.
The greatest thing about this repair was that I troubleshot the problem using the PartSelect website, ordered the parts and they arrived at my house in less than 24 hours.
Thank You.
Read less
570 of 611 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from San Clemente, CA
Parts Used:
WR55X10025, WR02X10552
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Fridge too warm, evaporator icing up
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
Read less
600 of 720 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More