DFSF9VKBABB General Electric Refrigerator - Instructions

Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.

unscrewed old filter by hand, installed new filter.

Until I figured out that the Metal cover on the divider door had to be removed (pried out) giving access to the hidden hinges. After that the hinges could be removed and replaced.Great with giving phone thou.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unscrewed 1 screw, removed panel, disconnected old icemaker and removed it, Added new icemaker, reconnected, replaced panel, replaced screw, & reset new icemaker. Started making ice almost immediately. Threw out entire first load of ice. Working great since! I wasn’t sure if it was the icemaker or the water valve to it so had a guy come out ($50) who confirmed it was the icemaker. He wanted $550 to replace it (part/labor). We bought the part here at Part Select for $185 (part/tax/delivery) and saved $265 on a job that took less than 15 minutes.

Leaking icemaker assembly was causing all of the ice cubes in the ice tray to freeze together. Remove ice tray, remove one Philips screw, pull the cover off, unplug the wires, remove the icemaker assembly by pushing tab and pulling the assembly at the same time. Replaced the water filter as well.

Went on the Internet to find the installation instructions.

In order to remove the condenser fan motor I needed to remove the fan blade. The blade is attached to the shaft with a press fit and there is a spring clamp that squeezes the blade to the shaft. Removing the spring clamp did not allow the fan to slide off the shaft because there must be some type of adhesive used in addition to the clamp. In forcing the blade off the shaft expect to damage the fan blade so that is why it was replaced. Very tight working area and difficult to get the leverage to pull on the blade.
The new blade will push on with a bit of force.

If this repair looks hard then you probably aren't doing it right. The key to doing this fairly easy upper hinge replacement is to pry the metal back off of the swinging panel attached to the door as a first step. Doing so exposes the screws that hold the hinges in the panel, and also the tabs that you must press in to release and remove the hinge covers. I accidentally broke the tabs on both hinge covers removing them, but I discovered that it didn't matter - I was still able to snap them both into place without having to replace them as well. Once you've released the hinge covers slide the panel upwards to reveal the entirety of the hinge, then push the hinge up with a flathead screwdriver so that it slides off of the anchor piece on the door. Slide the replacement part down onto the anchor, slide the swinging panel down and replace the hinge covers. From inside the panel reattach the screws (middle hinge only) and replace the panel parts including the metal back. Whole repair takes about 15 minutes.

Nothing to tell it was just a replacement part that the old part was removed and the new one inserted. Works like a dream Thanks

just had to unscrew old one put the new one in

Once I understand how to remove the old part the rest was very easy .
Had ice in a couple of hours .

Replacement ice maker was plug in unit, only needed to remove one screw holding plastic plate that hid plug and wiring. Plugged it in and reattached plate with screw and done!