CFE28UP2MJS1 General Electric Refrigerator - Instructions

I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.

Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.

While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring so it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I searched and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.

Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.

Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.

Remove old filter by pulling and not twisting and insert new filter by pushing in place.

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

Received the wrong spring. It is larger in diameter and the legs are too long. I used pliers to modify the spring for a temporary fix. Emailed CS about the wrong part and have never received any response back?

It was super easy! The glass came packaged and safe. Once I unwrapped it, I slid it in the firdge and it just popped into place. So super easy. And now we know for next time when taking it out to clean, (the reason it shattered in the first place) you should let the glass get to room tempurature before cleaning it with water or it will shatter! OOPS!

Move the refrigerator away from the wall.
Disconnect the refrigerator.
Remove bottom drawer.
Remove two criisper drawers.
Remove crisper drawer slides, one bolt near the front of each slide.
Push slides off pin at back.
Remove bottom panel at the back of the refrigerator to access fan.
Remove fan, held with a couple of screws.
Remove rubber gasket from around old fan and put the gasket around new fan.
install new fan and bolt in place.
Replace lower panel at back at back of refrigerator.
Reinstall drawer slides, hook at back and bold at front
Reinstall drawers.
Reconnect refrigerator power.
Push refrigerator back in place and adjust feed to hold in place.

Unplug refrigerator or turn off circuit breaker.

Insert knife blade or other thin blade into joint at bottom of screen bezel (where there is a color change) and pry up slightly until top of bezel pops out. Probably need to do this in several places until the entire top edge is out slightly. Pull the top of bezel out slightly and lift up to remove.

Remove 4 1/4" hex head screws to loosen control panel. Pull control panel out from door and remove three wiring connectors. You can now completely remove panel from refrigerator door.

Use T15 Torx driver to remove 5 screws on main circuit board and 2 on the small attached board. Remove and save plastic insulator piece.

Install new boards and insulator piece using the Torx screws. Reconnect the three wiring connectors and remount the control panel using the hex head screws.

Reinstall the screen bezel by sliding the bottom in first. Align the tabs on the bezel with the mating slots in the lower panel. When bezel is all the way down push in the top edge to engage the retainer clips.

Plug in refrigerator or turn on circuit breaker. Control should now go through the startup sequence.

Search online and came across PARTSELECT website!!! this is amazing when I opened the website and see a labeled drawing, so I know what part number to order, it arrived on time and when I install it fits very well, one lesson I've learned is whenever you removed this glass in the chiller box you have to reinstall the glass properly by inserting one of the side to the insert slide of the chiller so it will not move! I'M VERY HAPPY!!!! THANKS!!!

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long