Models
>
867-0121-0210
867-0121-0210 General Electric Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$22.12
This refrigerator defrost thermostat will cut out at 55 degrees F and kick back in when the temperature drops to 35 degrees F. It comes with connectors and the mounting brackets.
In Stock
$198.31
This condenser fan motor operates in a clockwise fashion. The fan itself has two 1/4 inch spade terminals. It carries 2 watts and 115 volts. This motor NO longer comes with cover for terminals.
In Stock
$78.51
This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.
In Stock
$75.49
This evaporator fan motor operates in a counter clockwise fashion. This motor's stack is 3/8 of an inch, and the motor has two terminals: one on the right side, and one on the left side. Use this evap...
In Stock
This part maintains the proper temperature. When the refrigerator reaches the desired temperature, this part interrupts the flow of electricity to the compressor which stops the cooling process.
No Longer Available
This white door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.
No Longer Available
Special Order
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 867-0121-0210
Viewing 4 of 4Fridge too warm
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clarence from Great Cacapon, WV
- Parts Used:
- WR60X177
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Wouldn't cool
I removed the 3 screws that held the motor and fan. Exchanged fan blades and reinstalled the fan and new motor
I was surprised to find the motor. The refrigerator/freezer was over 28 yrs old. Works fine now
I was surprised to find the motor. The refrigerator/freezer was over 28 yrs old. Works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Kalamazoo, MI
- Parts Used:
- WR9X355
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
I was getting irratic temperture control. I determined that tapping on the control would cause it to turn on or off as it should, on if the frig was to warm, or off if it was to cold.
The temperture control was mounted on the back wall of the refrigerator. One screw and a couple of tabs appeared to be the only attachments. After removing the screw, the freezer control appeared to be an issue since it was also attached to other parts. A little careful pushing revealed that the control knob simply snapped into the cover
... Read more
over the thermastat. Once unsnapped the thermastat and it's plastic cover were only attached by the three electricl connections. Pulling them loose off the terminals left the unit free. Simply examining how the old thermastat was mounted in the cover, and replacing it, and then reinstalling it in the frig was as breeze. All was well again.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Carpinteria, CA
- Parts Used:
- WR60X177
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Noisy Fan Motor - Bearing went out.
Moving the frig out and cleaning was the hardest part of this job - lots of dust collected over the 17 years the frig was in place. Once all the cleaning was done, with the frig out and back cover off (10 -12 screws taken off with nutdriver),I plugged the frig in and observed the the problem was a noisy fan motor. The motor is at the very
... Read more
back of the frig with easy access to the 3 brackets holding it in place.
Pull off the electrical clip. Remove the screw holding the bracket to the frame on the front bracket, leaving the bracket attacked to the fan. The other two screws remove from the fan, leaving the brackets in place.
Reverse the procedure when you receive the new part from PartSelect(great company to deal with)!
Pull off the electrical clip. Remove the screw holding the bracket to the frame on the front bracket, leaving the bracket attacked to the fan. The other two screws remove from the fan, leaving the brackets in place.
Reverse the procedure when you receive the new part from PartSelect(great company to deal with)!
Read less
Was this instruction helpful to you?
Thank you for voting!