Models
>
TBF21RBD
TBF21RBD General Electric Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This is a package of twelve Phillips-head screws. They can be used as replacement screws in refrigerators, ice makers, or freezers. Be sure to check that your appliance model is compatible with these ...
No Longer Available
Found at the end of the auger in the ice container - replace when the icemaker doesn't dispense ice.
No Longer Available
This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.
In Stock
Order now and your part arrives by Mar 28
In Stock
Order now and your part arrives by Mar 28
$22.91
This refrigerator defrost thermostat will cut out at 55 degrees F and kick back in when the temperature drops to 35 degrees F. It comes with connectors and the mounting brackets.
In Stock
Order now and your part arrives by Mar 28
In Stock
Order now and your part arrives by Mar 28
Special Order
$169.68
This condenser fan motor operates in a clockwise fashion. The fan itself has two 1/4 inch spade terminals. It carries 2 watts and 115 volts. This motor NO longer comes with cover for terminals.
Special Order
In Stock
Order now and your part arrives by Mar 28
In Stock
Order now and your part arrives by Mar 28
This part is used in between the blades for the ice maker.
No Longer Available
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for TBF21RBD
Viewing 8 of 8Leaking
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Greenville, NC
- Parts Used:
- WR62X23154
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Ice maker dispensed crushed ice but not cubes
Removed the ice bin and maker, then removed cover from the rear that covered the solenoid that controls the dispensing mechanism. Replace solenoid. The tricky part here is that there is a styrofoam cover around the solenoid pin that needs to be superglued into place and oriented properly during replacement. All electrical feeds snap ou
... Read more
t neatly and are easily replaced. Reassemble ice dispenser and bin, and viola, your back in business.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Great Cacapon, WV
- Parts Used:
- WR60X177
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Wouldn't cool
I removed the 3 screws that held the motor and fan. Exchanged fan blades and reinstalled the fan and new motor
I was surprised to find the motor. The refrigerator/freezer was over 28 yrs old. Works fine now
I was surprised to find the motor. The refrigerator/freezer was over 28 yrs old. Works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Kalamazoo, MI
- Parts Used:
- WR9X355
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
I was getting irratic temperture control. I determined that tapping on the control would cause it to turn on or off as it should, on if the frig was to warm, or off if it was to cold.
The temperture control was mounted on the back wall of the refrigerator. One screw and a couple of tabs appeared to be the only attachments. After removing the screw, the freezer control appeared to be an issue since it was also attached to other parts. A little careful pushing revealed that the control knob simply snapped into the cover
... Read more
over the thermastat. Once unsnapped the thermastat and it's plastic cover were only attached by the three electricl connections. Pulling them loose off the terminals left the unit free. Simply examining how the old thermastat was mounted in the cover, and replacing it, and then reinstalling it in the frig was as breeze. All was well again.
Read less
Was this instruction helpful to you?
Thank you for voting!