FGHT1846QP2 Frigidaire Refrigerator - Instructions

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

I pulled the old gasket off and thoroughly cleaned the entire refrigerator door, including the area where the gasket would pop into. Starting at the two upper corners, I pushed the corners into the ridge in the door and used my thumbs to press the gasket in along the top of the door. I then went about halfway down the door using my thumbs to push in the gasket. Then I pushed the lower corners in, taking my thumbs up either side of the door to finish installing that section then I pushed the bottom in, checking the lower corners to make sure they were secure. Then I closed the door and made sure the seal was secure on both sides of the door.

took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim

Easily removed the original door gasket starting at an upper corner by pulling the old gasket off completely. I then cleaned the area where the new gasket was to be pressed into the channel on the door of the fridge. I also cleaned the area on the fridge where the new gasket would seat upon completion of the installation.

With that completed, I began in the upper right corner of the door, easily pressing the new gasket into the channel on the fridge door. I then pressed the upper left hand corner of the gasket into place, into the channel on the door. I then pressed the entire upper horizontal part of the gasket into the channel along the top of the fridge door.

I then pressed the left and right vertical portions of the gasket into the channels on the fridge door. I then pressed the lower left corner of the gasket into place, followed by the lower right hand corner into place of the bottom channel of the door.

Lastly, I pressed the lower horizontal portion of the gasket completely into the channel of the bottom of the fridge door.

Finally, I rechecked all portions of the gasket to be sure they were securely fitted into the channel of the door.

Mission accomplished in less than 15 minutes. It's a piece of cake to make this repair!

Opened refrigerator door removed old door seal by pulling door seal loose from door with fingers installed new seal by pressing new seal back in by hand took roughly 10 minutes to do only issue I had was with delivery my package was sent to the wrong house and was received 3 days late

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

Replacing the gasket is easy, just remove the old gasket by pulling it out of its grove and push in the new gasket in place.

Pull off the gasket and replace by pushing into the grooves.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

I peeled off the torn door gasket. Then installed new door gasket pushing and pinching it into place

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????