The water filter in your refrigerator should be replaced every six months in order to provide clean, fresh tasting water. The filter absorbs impurities in the water like heavy metals, pesticides, and ...
This is an authentic air filter for refrigerators, sold individually. It helps to reduce strong odors and impurities found in the air. This filter needs to be replaced every 6 months to ensure it is w...
Designed for smooth drawer operation, this crisper pan roller attaches to the sides of the refrigerator’s crisper drawer, allowing it to slide in and out effortlessly. Over time, rollers can wear down...
If your fridge isn’t making ice or is leaking, this replacement ice maker can help. It includes everything needed to freeze and dispense ice automatically. It’s easy to install and works with many bra...
This crisper drawer cover helps maintain freshness by regulating humidity over the produce drawers. It features a glass surface that also functions as a shelf and includes rail brackets underneath for...
Sold individually.
This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer do...
Designed for 36-inch French-door refrigerators, this GREY magnetic door gasket ensures a secure seal to prevent air leaks and maintain optimal cooling conditions. It plays a critical role in regulatin...
If your freezer drawer isn’t sealing like it used to, this gray gasket might be the fix. It helps keep cold air inside and warm air out, so your food stays fresh and your appliance doesn’t have to wor...
This is an adjustable foot for your freezer, refrigerator, and dryer. This part supports your unit by screwing into one of the bottom four corners, and adjusting the height of your machine. If your ap...
The water inlet valve supplies water to the refrigerator ice maker and water dispenser.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears...
In Stock
Order now and your part arrives by Sep 27
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lisa Joy Lewis
August 17, 2026
The magnets came out of place and attached to cabinet. Door won't seal tight
For model number FPBC2277RF5
Hello Lisa, thank you for reaching out to us. Check the gasket channel. It could be torn or split. The flexible rubber pouch that contains the magnetic strip has split open and the exposed magnet is now directly contacting and sticking to the steel cabinet frame. Open the door slowly and inspect the gasket along the side that is sticking, if you can see a dark gray magnetic strip exposed through a tear or split in the rubber the gasket has ruptured and needs to be replaced. Both the doors use the same gasket, part number 241778315. If the rubber is intact but the entire gasket is pulling away from the door, the plastic retaining dart that snaps into the inner door liner has pulled free. In this case press the gasket dart firmly back into the groove along the full perimeter and check whether it holds. Cleaning any sticky residue from the channel first will help it reseat properly. We hope this information helps!
Was this helpful?
Thank you for voting!
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There i
... Read mores 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used
... Read more my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Simple three steps... 1) There's an front section to the ice-maker to take off. One Phillips screw is on the side, one screw is underneath near the inside of the refrigerator wall. Just unscrew and store. 2) There's a small plastic unit just inside the ice maker to take out. It's held in by a small nut that requires about a 4" extension
... Read more to reach. (You may be able to unscrew the nut with small needle-nose pliers). Just unscrew and take out the unit - the unit functions just to keep the ice maker wiring in place. 3) The wiring looks a mess, but there's just one wiring connector to the ice maker assembly. Unsnap it. The ice maker is not screwed in, it just slides in -- reach in and pull the assembly straight out; when it stops, lower it a bit and it will come free. Reverse the instructions to install the new unit.
