FGHI1864QP0 Frigidaire Refrigerator - Instructions

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

I removed the drawer from the support rails and placed it aside. I then removed the entire shelf that the rails were attached to. Each rail contained one (1) screw. I removed the screw, slid the support rails back approximately a 1/4 inch and they popped out. I replaced with the new rails, sliding them into place in reverse of how I removed the damaged ones & attached with the screw. I cleaned the shelf off and placed it back in the refrigerator, and placed the meat drawer onto the new rails. It actually took longer to clean the shelf than perform the repair.

I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

Reviewed the video on your website and followed the directions to the letter. Great video

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!

Frig area was at about 50 degrees and would not get cooler. Freezer was working great.
Empty the freezer and remove the two screws that hold the back panel of the inside of the freezer on. Pull the panel out and you will see the fan that is mounted to the back of the panel. If the fan is not running, disconnect it (quick connector) and check to see if there is voltage coming to it from the connector (should be 120VAC between the two wires). If there is power, and the fan was not working, replace the fan.

Fan just snaps into the holder on the back panel and plugs into the quick connector. Make sure you clear any ice build-up in the hole between the freezer and the frig that the fans blows through. Put it back together and verify the fan runs.

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.

I pulled the old gasket off and thoroughly cleaned the entire refrigerator door, including the area where the gasket would pop into. Starting at the two upper corners, I pushed the corners into the ridge in the door and used my thumbs to press the gasket in along the top of the door. I then went about halfway down the door using my thumbs to push in the gasket. Then I pushed the lower corners in, taking my thumbs up either side of the door to finish installing that section then I pushed the bottom in, checking the lower corners to make sure they were secure. Then I closed the door and made sure the seal was secure on both sides of the door.

took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim

Easily removed the original door gasket starting at an upper corner by pulling the old gasket off completely. I then cleaned the area where the new gasket was to be pressed into the channel on the door of the fridge. I also cleaned the area on the fridge where the new gasket would seat upon completion of the installation.

With that completed, I began in the upper right corner of the door, easily pressing the new gasket into the channel on the fridge door. I then pressed the upper left hand corner of the gasket into place, into the channel on the door. I then pressed the entire upper horizontal part of the gasket into the channel along the top of the fridge door.

I then pressed the left and right vertical portions of the gasket into the channels on the fridge door. I then pressed the lower left corner of the gasket into place, followed by the lower right hand corner into place of the bottom channel of the door.

Lastly, I pressed the lower horizontal portion of the gasket completely into the channel of the bottom of the fridge door.

Finally, I rechecked all portions of the gasket to be sure they were securely fitted into the channel of the door.

Mission accomplished in less than 15 minutes. It's a piece of cake to make this repair!

Followed the steps in the video on your site, really easy to do.

Opened refrigerator door removed old door seal by pulling door seal loose from door with fingers installed new seal by pressing new seal back in by hand took roughly 10 minutes to do only issue I had was with delivery my package was sent to the wrong house and was received 3 days late