Models
>
RTG140GCH2A
RTG140GCH2A Frigidaire Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for RTG140GCH2A
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$27.45
This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM...
In Stock
Order now and your part arrives by Aug 16
In Stock
Order now and your part arrives by Aug 16
In Stock
Order now and your part arrives by Aug 16
This white door gasket is used to make an air-tight seal for the cabinet when the door is closed.
No Longer Available
This white hinge pin bearing pivots the freezer and refrigerator door.
No Longer Available
On Order
In Stock
Order now and your part arrives by Aug 16
In Stock
Order now and your part arrives by Aug 16
This almond door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.
No Longer Available
Common Problems and Symptoms for RTG140GCH2A
Viewing 6 of 6Light not working
Fixed by these parts
How to fix it
Door Sweating
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Won’t start
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Gurnee, IL
- Parts Used:
- 216594300
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The compressor would not run.
I removed the cover, used a multimeter to test the compressor circuit, and found the compressor start relay to be defective.
Ordered a new one and installed it when it arrived.
Ordered a new one and installed it when it arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherman from Tuttle, OK
- Parts Used:
- 216594300
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Compressor was short cycling
Removed the cowling with a square drive screw driver, removed the spring clip from the cover of the compressor controls with a screw driver, pulled off the old compressor start relay and replaced it with the new part. Since other problems could have caused the compressor to short cycle this was a "replace the part and hope it would work"
... Read more
since that would be the most common reason and it was not a very expensive part.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Forest, VA
- Parts Used:
- 5303917590
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Wrench (Adjustable)
Drip pan had rusted & was leaking water on the floor
The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the p
... Read more
an above the threads of the bolt so as not to damage the threads). I still had to cut half the bolt away with a hack saw by replacing the nut and cutting a third of the bolt away (above the nut), so the new pan would fit. Putting the new pan on was a breeze after that. It may be easier to just cut the bolt off altogether on top of the compressor and use the wire clips per the instructions supplied with the kit to install the new one.
Read less
Was this instruction helpful to you?
Thank you for voting!