Models > RS249GCH2

RS249GCH2 Frigidaire Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for RS249GCH2

Viewing 10 of 10
Keep searches simple, eg. "belt" or "pump".
$21.95
This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM...
In Stock
Order now and your part arrives by Nov 21
During automatic defrosting, this refrigerator thermostat permits heater operation while the evaporator coils are cold, then breaks the circuit at the cutoff temperature to help prevent overheating. I...
In Stock
Order now and your part arrives by Nov 21
To drive the fan that circulates cold air through the refrigerator and freezer compartments, this evaporator fan motor uses a center hub mount and rotates clockwise. The shaft measures 1/8 inch in dia...
In Stock
Order now and your part arrives by Nov 21
Interior lighting depends on a secure connection between the bulb and its power supply. This refrigerator light socket holds the bulb in place and provides the electrical contacts needed to illuminate...
In Stock
Order now and your part arrives by Nov 21
This evaporator fan blade is used to move cooled air through the refrigerator or freezer compartments when driven by the fan motor. A cracked, warped, or loose blade may vibrate, strike nearby parts, ...
In Stock
Order now and your part arrives by Nov 21
Sold individually.
In Stock
Order now and your part arrives by Nov 21
$20.01
This multi-use screw fits various appliances and tools such as, freezers, refrigerators, wall ovens, washers, ranges, dishwashers, dryers, microwave oven combos, combos, wine and beverage coolers. *Pl...
In Stock
Order now and your part arrives by Nov 21
$57.89
Sold individually.
Special Order
This white hinge pin bearing pivots the freezer and refrigerator door.
No Longer Available
Sold individually.
No Longer Available
This filter drier is used to remove moisture and trap small particles in the refrigerator sealed refrigerant circuit. It helps keep dirt, metal fragments, and moisture from moving through the cooling ...
In Stock
Order now and your part arrives by Nov 21
This part turns the light on/off as the door opens and closes.
Special Order

Common Problems and Symptoms for RS249GCH2

Viewing 13 of 13
Fridge too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Light not working
Fixed by these parts
Fixing Fixing
How to fix it
Freezer not defrosting
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing Fixing
How to fix it
Fridge runs too long
Fixed by these parts
Fixing
How to fix it
Freezer too cold
Fixed by these parts
Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
Fixing
How to fix it
Fridge too cold
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing
How to fix it
Too warm
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jordan from Maumee, OH
Parts Used:
5308000010, 5300158289
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Noisy fan
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including th e brackets.
6. Install the new motor and fan onto the mounting bracket.
6a. Attach the green ground to the mounting bracket.
7. Screw the two gold screws back into the freezer.
8. Attach the new wiring harness. Note, the old harness had a mounting hole/space for it to connect to the wiring harness of the freezer. The new motor's harness was not long enough for this, so it is connected freely to the freezer harness.
9. Use the hair dryer to melt any ice that may have formed on the coils and hole where the fan goes.
10. Turn the freezer on to see if the fan turns on.
11. Reinstall the back panel.
All done!
153 of 180 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Alexandria, VA
Parts Used:
218906802
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light socket melted around bulb
After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.
66 of 108 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROY from PENSACOLA, FL
Parts Used:
5308000010, 5300158289
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
The Evaporator Fan Burnt Up
The fan motor all but caught the inside of the freezer on fire . Had to remove then clean, and I mean clean the walls of the freezer . Then had to pry out the old fan without breaking anything . Replacement of new fan was quick and easy because all the parts that I needed were in the bag
29 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!