Models
>
MRTG20V8PS0
MRTG20V8PS0 Frigidaire Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MRTG20V8PS0
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
$58.25
This is a white plastic door shelf bin for your refrigerator. It is attached to the inside bottom of the refrigerator door shelf where it helps to contain items such as jars and condiments. This part ...
In Stock
Order now and your part arrives by Apr 25
$52.50
This glass shelf sits above the crisper drawers in your refrigerator. This part is just the glass, there are no brackets or additional mounting hardware (these can be purchased separately if needed). ...
In Stock
Order now and your part arrives by Apr 25
$131.53
Keep your fridge running efficiently with this 21-inch white door gasket. It forms a tight seal to keep cold air in and warm air out, helping your food stay fresh and your appliance work properly. Ins...
In Stock
Order now and your part arrives by Apr 25
This sliding glass shelf fits select Frigidaire, Electrolux, Kenmore, and Tappan refrigerators. It features a spill-safe edge to contain messes, a sliding design for easy access, and a pan hanger for ...
In Stock
Order now and your part arrives by Apr 25
$16.35
This screw is used to secure the handle to your refrigerator and comes in a pack of four. This genuinely sourced part can be loosened and tightened with a Phillips-head or square-head screwdriver. Wit...
In Stock
Order now and your part arrives by Apr 25
$38.45
If your freezer is cold but your fridge feels warm, this defrost thermostat might be the issue. It helps control the temperature during the defrost cycle so things don’t overheat. When it’s not workin...
In Stock
Order now and your part arrives by Apr 25
$24.00
Sold individually.
This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer do...
In Stock
Order now and your part arrives by Apr 25
In Stock
Order now and your part arrives by Apr 25
In Stock
Order now and your part arrives by Apr 25
$93.24
This freezer door gasket creates a tight seal to keep cold air in and warm air out, helping your fridge run efficiently. It fits select Frigidaire, Electrolux, and Kenmore models and helps prevent fro...
In Stock
Order now and your part arrives by Apr 25
This is a replacement condenser fan motor kit for your refrigerator. This six-piece kit contains foam tape, 2 screws, the fan blade, the new motor mounting bracket, and the condenser fan motor. The co...
In Stock
Order now and your part arrives by Apr 25
$13.07
This door hinge bushing, or hinge bearing, is a genuine OEM replacement part for your refrigerator. The hinge bearing helps the refrigerator door stay on track when opening and closing, ensuring it is...
In Stock
Order now and your part arrives by Apr 25
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for MRTG20V8PS0
Viewing 15 of 15Fridge too warm
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Door Sweating
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Frost buildup
Fixed by these parts
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
How to fix it
Light not working
Fixed by these parts
How to fix it
Fridge runs too long
Fixed by these parts
How to fix it
Freezer too cold
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Clicking sound
Fixed by these parts
How to fix it
Fridge too cold
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew from Washington, DC
- Parts Used:
- 242193213
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator door gasket torn
No instructions included, so it took a little bit of staring at the new part to figure out how it works. The barbed ridge on the gasket fits into a slot on the door. The flat face of the gasket has an internal magnetic strip that helps keep the seal tight against the steel face of the refrigerator. Installation requires no tools. This is
... Read more
the basic process:
1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long.
2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free.
3) Set aside the old gasket
4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door.
5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated.
6) Once you have the new gasket installed, close the door to make sure everything fits OK.
7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door.
8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore.
9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...
1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long.
2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free.
3) Set aside the old gasket
4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door.
5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated.
6) Once you have the new gasket installed, close the door to make sure everything fits OK.
7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door.
8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore.
9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Hanover Township, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
evaporator coil kept freezing up, refridgerator warm.
This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from Camp Hill, PA
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Broke a blade off of the fan
When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!