The water filter in your refrigerator should be replaced every six months in order to provide clean, fresh tasting water. The filter absorbs impurities in the water like heavy metals, pesticides, and ...
This is a genuine Frigidaire part for your refrigerator. This is an ice maker, which connects to the water lines to provide fresh ice. The most common reason to replace this part is if your refrigerat...
Sold individually.
This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer do...
This crisper drawer cover assembly is for refrigerators.
The crisper drawer cover assembly includes the crisper drawer cover frame and the insert that covers the drawer. The assembly may include mu...
This is an adjustable foot for your freezer, refrigerator, and dryer. This part supports your unit by screwing into one of the bottom four corners, and adjusting the height of your machine. If your ap...
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mark
November 11, 2023
My icemaker is dispensing ice extremely slow. What can be the problem it is making plenty of ice.
For model number FFHB2750TD5
Hello Mark, Thank you for your inquiry. It could be an issue with the ice dispenser solenoid, the auger motor, or the module with switches. See if the auger turns freely and there are no ice jams, check the plunger on the solenoid to make sure it is moving up and down smoothly. You can test the switches on the module with a multimeter and check for any damaged wires. Good luck with your repair.
My ice maker is dispensing ice and crushed ice when cube button is pressed. What could be the problem. Tks
For model number FFHB2750TD5
Hi Mark, thank you for the question. Based on our understanding, the issue is because of the ice dispenser solenoid, part number FIX8691994. The ice dispenser solenoid allows cube or crushed ice to be dispensed on demand. We would recommend checking this part to fix the issue. We hope this helps!
The auger is moving the ice towards the drum blocking the entrance to the drum therefore not dispensing the ice as it accumulates above and around the drum. I noticed they’ve changed the design on the auger with less spirals, could this solve my problem thank
For model number FFHB2750TD5
Hello Mark, Thank you for writing. Checking this model number provided the auger has not changed. The new augers will not work in this bucket. The Auger for this model is only sold as part of the Bucket Fix Number: FIX10057214. We hope this helps!
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There i
... Read mores 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
Simple three steps... 1) There's an front section to the ice-maker to take off. One Phillips screw is on the side, one screw is underneath near the inside of the refrigerator wall. Just unscrew and store. 2) There's a small plastic unit just inside the ice maker to take out. It's held in by a small nut that requires about a 4" extension
... Read more to reach. (You may be able to unscrew the nut with small needle-nose pliers). Just unscrew and take out the unit - the unit functions just to keep the ice maker wiring in place. 3) The wiring looks a mess, but there's just one wiring connector to the ice maker assembly. Unsnap it. The ice maker is not screwed in, it just slides in -- reach in and pull the assembly straight out; when it stops, lower it a bit and it will come free. Reverse the instructions to install the new unit.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used
... Read more my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!