E32AR75FPS1 Electrolux Refrigerator - Instructions

The old gasket was obviously gapping, partially from age and partially from damage during a move. To make the repair, I loosened the screws that are under the gasket and hold it in, but did not remove them. Once all were loose, I removed the old gasket, then starting at the top, ran a thin bead of food grade RTV under the portion of the door that captures the gasket. I put the sealant on that edge only, then carefully worked one of the short edges of the gasket under the plastic and tightened all but the corner screws. I then ran the RTV down the inside of the hinge side of the door and repeated the process, this time tightening the top screw and the hinge side screw at the top, but leaving the bottom most screw loose. I repeated the process on the opening side of the door. The bottom was the hardest because the gasket seemed just a little long and it was hard to get the RTV up and behind the door portion, but after a couple tried I got a good bead of sealant then slid the gasket under the door capture and tightened all the remaining screws. After closing the door, it was obvious that there were places were it did not seal well. I used some cardboard strips, cut from the box the gasket came in, to place inside the freezer, between the hard plastic of the door and the inside of the gasket where it laps over the screws. This helped a lot, but there were still a couple small areas, so I used more cardboard, from the outside, between the main portion of the gasket and the rim of the gasket. This eliminated all the gaps. I let this sit overnight and this morning removed all the cardboard for a great sealing freezer.

Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searches on the internet to finally figure this part out. From there on out it went smoothly. Old base came out with two screws. Reversed process for reinstall of new base. Water hoses just slipped back into place and locked themselves in. Just takes a little patience.

Turned freezer off at themostat and unplugged freezer. Removed 2 screws at front 2 at the back and 2 at the top. Lowered top cover and removed evaporator fan bracket (2 more screws) removed themostat capulary tube( 1 screw and bracket) then unplug fan motor. Removed motor from bracket (2 screws). Put on new fan motor then removed fan blade from old motor and put on the new motor. Remounted fan motor bracket and thermostat capulary tube. Remounted top cover, plugged freezer in the set the thermostat to 4 and freezer is working fine and doing its job. I orderedmotor on a Sunday and it was shipped on Monday and I received said part at 7:pm on Wednesday.

Removed old gasket by loosening all the screws. Inserted new gasket. Be careful to prop up the plastic shell so that ALL screw holes line up, especially at the bottom, and that shell is not tilted. Then carefully insert gasket inch by inch and fasten very other screw, best from bottom up. Make sure that the gasket lip is clearly under the shell and engaged with it. Before you do anything you have to straighten out ALL the kinks with a heat gun. Do not get too close. It takes a while.

Silly me. It couldn't possibly be the filter because it's worked for the last 9 months with no problems. Decided to replace the water filter base first. Repair was easy. I saw someone had trouble removing tubes from old base and I gave it a couple of tries to no avail so decided to cut the lines instead. Made it even easier. After repair, water continued to leak. So, replaced the filter itself and voila - leak fixed. Make sure you check the filter first. My mistake turned a $40 - 10 second repair into a $100 - 20 minute repair. Good Luck!

The called for part is the wrong size due a false correlation between the called for part number and the PartSelect number. I order twice and each time it was a 31 by 65 in. gasket not the appropriate 31 by 60 in.. Both were returned but no resolution.

Removed evap cover from Commercial Refrigerator. Removed mounting screws from Evap motor mount. Replaced evap fan motor. Repositioned. Reinstalled evap cover. Tested . This motor was hard to find locally. Glad I called.

Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.

I removed the shelves, unscrewed the cover panel of the fan motor and regulator dial, disconnected the fan motor from power, unscrewed 2 screws holding the motor to the mounting bracket and put the new motor in it's place. New motor had no thread in the mounting holes, so I put new tread in so I could use the 2 screws. Another option would have been to drill all the way through the mounting holes and use longer screws or bolts. Of course I turned the power off before I started repairs. Freezer runs like new now. Technicians wanted $400 for the job, while it cost me a mere $55 for the Motor.

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

After receiving the part in the mail I removed it from the box and laid it flay on the floor. I had to use a hair dryer to CAREFULLY work it flat from the shipping. This took about an hour and a glass of scotch. I then let it sit over night to get the gasket as flat as possible. The next day I unloaded the freezer, unplugged it, and pulled the old gasket off by removing all the screws. I carefully slide the seal out of the track and did not remove the cover from the door. I left the door open for a couple hours to completely melt all of the ice and clean out the interior. I put the top and bottom of the seal in the track and carefully worked the sides in. It helps if you use a few screws to hold the gasket in place. Then easily pull the gasket to position it correctly. Using a screw gun with a clutch will help since there are quite a few screws. Check the seal by closing the door and see how it seals. It may be necessary to use the hair dryer to get the seal to pull up to the freezer body. Close the door and plug it it. Wait a few hours before putting in any food. Take your time and having a helper will make it go quicker.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

I did watch a repair a utube video which I asked for when ordering. Pretty much followed most of the directions but:

started in left corner an lossed all screws from left to right. took off old gasket in small sections and inserted the new gasket and semi tighten screws

proceeded down left side then right little by little as above. to get to bottom of door.

bottom corners were a little snug to get them into place. the last corner was snug but once connected. tighten screws not too tight. You dont want to strip them.

test door with piece of paper.

if paper is not a snug tug, you can adjust gasket with a hair dryer set to low.

it was easy. freezer is all set.

Partselect was great to deal with, support verified the part number was correct for my freezer and help with that video.

Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!