Models
>
CRTE187EW4
CRTE187EW4 Crosley Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CRTE187EW4
Viewing 7 of 7Manuals & Guides for CRTE187EW4
Click to downloadInstall
Installation Instructions
(0.8MB)
Manual
Owner's Manuals
(1.11MB)
Wiring
Wiring Diagram
(0.22MB)
Keep searches simple, eg. "belt" or "pump".
$58.25
To hold bottles, jars, and condiments on the lower shelf on the inside of the refrigerator door, this white plastic door shelf retainer attaches to the inner door panel and helps keep items in place w...
In Stock
Order now and your part arrives by Nov 22
$43.95
This clear plastic crisper pan is used to provide a separate storage space for fruits and vegetables in the refrigerator fresh food section. You can see the stored contents through the transparent sid...
In Stock
Order now and your part arrives by Nov 22
$53.53
A clear food-storage surface above the crisper drawers is provided by this glass shelf insert. Measuring approximately 23.82 inches wide by 15.5 inches deep, it fits into the existing supporting frame...
In Stock
Order now and your part arrives by Nov 22
For select refrigerators, the white right-hand track supports the meat pan. Check the refrigerator model number to confirm fit before ordering. This is an OEM replacement part.
In Stock
Order now and your part arrives by Nov 22
$32.78
Measuring approximately 16.75 inches long, this white plastic door handle offers a handhold for opening the refrigerator or freezer door on specified models. Cracks, broken mounting tabs, or damage th...
In Stock
Order now and your part arrives by Nov 22
$142.16
To help keep cold air inside and warm air carrying moisture out, this white refrigerator door gasket seals the fresh food section. Its flexible vinyl edge fits around the inner door panel and makes co...
In Stock
Order now and your part arrives by Nov 22
$41.55
This 120 volt, 60 hertz defrost timer is used to switch the refrigerator into a 30 minute defrost cycle after eight hours of compressor run time. The cycle allows the heater to clear frost from the ev...
In Stock
Order now and your part arrives by Nov 22
This is a genuine OEM replacement crisper drawer cover for your refrigerator. It measures approximately 27 inches by 20 inches and does not include the glass insert for the self. You can reuse the gla...
In Stock
Order now and your part arrives by Nov 22
$59.15
This left side rail is used to support and guide the refrigerator meat drawer as it slides open and closed. With a cracked or broken rail, the drawer may sag, catch, or move unevenly. Sourced directly...
In Stock
Order now and your part arrives by Nov 22
$21.95
This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM...
In Stock
Order now and your part arrives by Nov 22
$17.47
Four #10-16 screws secure a refrigerator or freezer door handle to the door. This OEM kit includes screws that are 0.500 in. long, with a Phillips or square drive. Confirm compatibility with your appliance before buying.
In Stock
Order now and your part arrives by Nov 22
$41.14
During a refrigerator defrost cycle, this thermostat helps protect the evaporator from overheating. Cooling problems or a failure to defrost can point to an issue in the defrost system, but do not con...
In Stock
Order now and your part arrives by Nov 22
Common Problems and Symptoms for CRTE187EW4
Viewing 17 of 17Fridge too warm
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Light not working
Fixed by these parts
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Door Sweating
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Fridge runs too long
Fixed by these parts
How to fix it
Won’t start
Fixed by these parts
How to fix it
Fridge too cold
Fixed by these parts
How to fix it
Frost buildup
Fixed by these parts
How to fix it
Freezer too cold
Fixed by these parts
How to fix it
Clicking sound
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew from Washington, DC
- Parts Used:
- 242193213
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator door gasket torn
No instructions included, so it took a little bit of staring at the new part to figure out how it works. The barbed ridge on the gasket fits into a slot on the door. The flat face of the gasket has an internal magnetic strip that helps keep the seal tight against the steel face of the refrigerator. Installation requires no tools. This is
... Read more
the basic process:
1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long.
2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free.
3) Set aside the old gasket
4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door.
5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated.
6) Once you have the new gasket installed, close the door to make sure everything fits OK.
7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door.
8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore.
9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...
1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long.
2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free.
3) Set aside the old gasket
4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door.
5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated.
6) Once you have the new gasket installed, close the door to make sure everything fits OK.
7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door.
8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore.
9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Linton, ND
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door handle broke off
First I removed the top screws, then I slide it off the lower screw that is hidden behind the handle. I replaced the handle by sliding it onto the bottem first then attaching it onto the top with the two top screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Hanover Township, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
evaporator coil kept freezing up, refridgerator warm.
This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.
Was this instruction helpful to you?
Thank you for voting!